Lee's micra dot

lee k0011 said:
Four in total on mine. But it was a pig to get off.. Every thing had just rusted solid in to one lump, so it had to be cut off instead of just unbolted..

But worth the hassle as the rattle was doing my head in.. Sounds so much better now, especially at high revs..
Click to expand...

So you have no exhaust shield then? Is that safe? Mines annoying me slightly

Sent from my GT-I9100 using Forum Runner
 
skymera said:
So you have no exhaust shield then? Is that safe? Mines annoying me slightly

Sent from my GT-I9100 using Forum Runner
Click to expand...
Yep perfectly safe in my experience..Fitted a new down pipe to my sisters K11 about three years ago,and never put a heat shield on that. That has done 200 mile trips with no problems at all..

Any way. i thought you had a Janspeed on yours ??
 
lee k0011 said:
Yep perfectly safe in my experience..Fitted a new down pipe to my sisters K11 about three years ago,and never put a heat shield on that. That has done 200 mile trips with no problems at all..

Any way. i thought you had a Janspeed on yours ??
Click to expand...

Oh I thought it was the heatshield further back, towards the centre pipe bend and backbox. I have a bit removed but faf putting it back, just laziness really.
 
The micra faces an uncertain future now :(
zzz 003.JPG
 
odd_ball said:
Hang on... Are you jacking it up under that rusty panel?
Click to expand...
Yes but there wasn't a hole there when i jacked it up. Only went under there to paint over an old repair and ended up with this :(. Moved the jack sharpish tho after i released..

So the plans now are ether to buy a welder and sort it my self, or i have found another pre face lift not far away, with only 40K on the clock.
Reluctant the later tho, as i have put alot of work in to this one.

Oh and i did find two other patches, but they are not structural so nothing to worry about ..
 
lee k0011 said:
Yes but there wasn't a hole there when i jacked it up. Only went under there to paint over an old repair and ended up with this :(. Moved the jack sharpish tho after i released..

So the plans now are ether to buy a welder and sort it my self, or i have found another pre face lift not far away, with only 40K on the clock.
Reluctant the later tho, as i have put alot of work in to this one.

Oh and i did find two other patches, but they are not structural so nothing to worry about ..
Click to expand...
If you can do it gor the cost of the welder and labour in 200 quid. Fix her. If more shoot her for airplane meat. Once you have rust its a losing battle.

Sent from my NOVO7PALADIN using Tapatalk 2
 
lee k0011 said:
Yes but there wasn't a hole there when i jacked it up. Only went under there to paint over an old repair and ended up with this :(. Moved the jack sharpish tho after i released..

So the plans now are ether to buy a welder and sort it my self, or i have found another pre face lift not far away, with only 40K on the clock.
Reluctant the later tho, as i have put alot of work in to this one.

Oh and i did find two other patches, but they are not structural so nothing to worry about ..
Click to expand...

Hope it works out! :(
 
Well things today just went from bad to worse :(

Got it fixed for £70. But spent the day waiting for the police and sorting out the new glass, when i was meant to be out with the family..

Wish i could have court the t***s that did this, but they will prob get away with it:mad:
Micra smash 004.JPG
 
Was go'n to do the welding this weekend, but when i went to get the steel they didn't have a piece small enough for me to fit in to my car..
So that will just have to wait till next weekend now..
prep 006.JPG
 
Had another play with the wheels. Jacked it up by the axle to keep it under load, and they tucked in quite nicely :)
prep 001.JPG


I also tryed the wheel on the wrong way round to see if it gave any less poke..

Wheel the rite way round
prep 002.JPG


Wheel the wrong way round
prep 004.JPG

prep 003.JPG
 
Just made the first section to be welded in. But it is raining now and need to go out in a bit, so it will have to wait till tomorrow ...
fab1 001.JPG
 
Good fight going on with this K11 , keep it up! :)

I´ve welded a dozen datsuns and nissans back to life (including that blackmask K11 i use as a daily driver for this winter), it can be boring sometimes but pays the price at the end for sure!
 
cherrytuner said:
Good fight going on with this K11 , keep it up! :)

I´ve welded a dozen datsuns and nissans back to life (including that blackmask K11 i use as a daily driver for this winter), it can be boring sometimes but pays the price at the end for sure!
Click to expand...
This was a pain of a job to do with the car on the ground tbh.
Just hope it is all good for the M.O.T in feb now!
 
No more whole:)
Welding wasn't the neatest tbh, but it was solid enough to be hit with a hammer and not budge..
Put plenty of underseale on it to keep it rust free..
lets just hope the M,O,T man is happy with it..
zz 003.JPG
 
lee k0011 said:
Hope it isn't as bad as mine was dude!
Click to expand...


Not yet , has started around the hole what has been made for rust protection use....and now the hole is a bit bigger :p

Would be best to repair as fast as possible because of the salt they put to roads here now. But i don´t know when i´ll have the time for it :(
 
SuperUno said:
I am about to do my rocker cover like yours, couple of questions for you.

Did you mask the writing or just sand it down after painting?
What allen bolts did you use, the OEM screwsa are a bit too manky to reuse.
Click to expand...
I used masking tape. But if i were to do it again, i would just sand after painting. Looks a lot simpler, and saves time..
Not sure about the bolts tho. Got loads of them from building bikes. I think they are about 25mm long, but cant remember the thread size sorry..
 
lee k0011 said:
I used masking tape. But if i were to do it again, i would just sand after painting. Looks a lot simpler, and saves time..
Not sure about the bolts tho. Got loads of them from building bikes. I think they are about 25mm long, but cant remember the thread size sorry..
Click to expand...

Thanks, will paint and sand back then. Anyone else know a suitable bolt ?
 
Got a new steering wheel in the week.. Looks a bit tatty, but is a lot nicer to hold than the mountney..
Hoping to make a new back box for it this month. Got two weeks off for xmas, so will try to sort it then.
a11 288.JPG
 
Failed:(
Needs a new front cross member and a repair on the inner sill...

Just need to price it up and decide whether to fix or just get a new micra...
 
nice another person from north wales!

on another note, reguarding the welding, i suppose it depends on what its going to cost to fix :/
sometimes its better to cut your losses and start again on something better
 
Danieljs12 said:
nice another person from north wales!

on another note, reguarding the welding, i suppose it depends on what its going to cost to fix :/
sometimes its better to cut your losses and start again on something better
Click to expand...
I have got my eye on a couple of other micras. But it would brake my hart to scrap it:(
Where about in north wales are you??
 
in in kinmel bay mate not to far from you..

from experience usually when rust start good you onto a loosing battle! which is a shame, if you pay to get what needs doing on the mot done you may then find something else, and then something else, you might get another year out of it.. but then chances are your likely gonna be paying out for welding again
 
Well it wont be the first time it has been welded.. This will be the 3rd time i have had the cross member welded.
So the plan was to do it properly and start replacing whole panels instead of just putting in patches. But i just don't have time to do that my self atm.
 

Similar threads

C
fixing micra.
Replies
0
Views
628
camoxodka
C
E
Breaking Micra K11 news!!!
Replies
33
Views
4K
moonmoths
M
Rogue
The nearly everlasting Nissan Micra
Replies
2
Views
952
Rogue
Rogue
M
Taking The Micra To The Nurburgring
Replies
2
Views
623
Enuo
Enuo
B
Prospective Micra Owner
Replies
3
Views
729
backseateducation
B
Back
Top