Search results

As the title. Half way through replacing my manifold and all the bolts have sheared off in the cat so could do with a replacement. Also I can't get the lambda sensor out the old mani so if anyone has one of those too Cheers Matt

As the title really, what size torx bit to remove the airbag from my k11 so I can remove the wheel. Also while I'm here what size is the nut which holds it on? Cheers Matt

Anyone know where to get some from?

Hey everyone, can't find the answer to this anywhere, what size is the spline on a 1995 K11 Micra non pas? I have a momo steering wheel from my old MX5 which I would like to fit and I have seen a boss on eBay for £8 which says fits all models (heard it before) and the splines are 15.5mm. Will...

Hi all, Thought I would start a thread about my second Micra. This is my last one bought for £175, rusty as and with a knackered clutch. Sorted it all out cleaned it up and it was a good fun little car. Sold it on after a while as it wasn't getting used. So I picked this up yesterday. 1...

Hi all, I have just fitted a cheapo stereo in my K11 all works fine. but i have two questions! 1. is it likely that my car K11 shape will only have one front speaker (passenger side) only sound comes from this side. my mates mk2 fiesta only has one from the factory but that is an '86 car not...

Hi all, Where would be the best place to source a decent 1.3 engine for the micra? and how much should they cost? ebay seems to be very expensive (more than the value of my car!) Just curious really, would be interesting to know. Cheers Matt

Went to go out in her last night, just kept turning over but didn't catch, i only tried a couple of times then took my company car as i was running late. I think it must be damp? it was raining heavily all day yesterday. i am going to get some damp start and eas start at lunch as i have run...

Right many of you may have read a couple of threads i've started about gearbox/clutch issues with my car. i think i have come to the conclusion that the gearbox has had it! Its done 117k miles and it's getting very hard to select first gear, i think the clutch arm mech may have something to do...

Is there anywhere to buy a new rear engine mount for the K11 1.0 manual? search the internet hasn't bought up anything at present. Cheers Matt

Hi all, When i pull away in first, sometimes i get a judder which feels like the clutch engaging. Changing gear normally is no problem. Only when setting off, could this be the alignment/how tight the pressure plate is? engine/transmission mounts or something else? I will be changing the...

My friend has asked if I could have a look at her car, needs two new wheel bearings and mid section of exhaust. The exhaust is ok just not fun by the side of the road. Has anyone done the bearings? Are they easy? I believe they are sealed bearing units is it a case of removing a circlip and...

Is it as easy as unhook from gearbox end, then pedal and bulk head. Can it be done without removing too much? Reason I ask is after changing my clutch I have run out of adjustment, I think because the cable has stretched so much over the last 15 years. Would like to change it for peace of...

Thought i would post in here as well as K11 Does this circlip look ok for use on a driveshaft? it came off my K11 o/s, wheel end. The one on the n/s was closer to a full circle with no notches. What are your thoughts? Cheers Matt

Hi All, Happy New Year! I started putting the gearbox back in last night after changing the clutch. as i inspected the O/S driveshaft gaiter i thought i would replace it as it was close to spliting. I changed the n/s one before Christmas so i understand the process although i am having a...

I'm having problems removing the gearbox. I don't want to break anything whilst prying it off. What is the best method for removal/depredation from the block Really appriciate any help with this Matt

Right then. I got an instrument cluster with a rev counter in for cheap of ebay, I thought it would just be a straight swap for my standard one. When I recieved it yesterday I went straight ahead and fitted it. during the process I noticed a few of the bulbs on the back were in different...

Hi all what's the capacity of a k11 1.0 gearbox and what grade is required? Cheers Matt

Radiator bracket stud size? Does anyone know what size this is? M6? Cheers for your help Matt

I need a couple of nuts and bolts for the bottom radiator brackets. Does anyone know what size they are? M6? Cheers for your help. Going to a fasteners place up the road at lunch. Would be good to know. Matt