Search results

  1. C

    Clicking Relay

    Anyone had a clicking relay after they turn the ignition switch off. Or when they go to start the car, Just before cranking? It was weird, turned my car off the other day and I heard a clicking noise from under the dash?
  2. C

    Selling My 2 Door 97 Micra - Low K\'s

    Forgot to metion it's got central locking too!
  3. C

    Selling My 2 Door 97 Micra - Low K\'s

    Has good A/C but no Power Steering! It's an LX Micra!
  4. C

    Selling My 2 Door 97 Micra - Low K\'s

    OK! I'm selling my micra cause I've upgraded to a skyline. Would of kept it but the skyline was too good a deal to pass up. This one's been well looked after mechanically with some minor body defects from the previous owner. Has just done over 124K. Five speed manual. 14" CSA Mags with new...
  5. C

    new pics of our micra

    Likey Likey alot!
  6. C

    Installing Japanese 2000 model bubble rear light clusters on an Australian micra

    It's a prick of a job! Just got done sending you some instructions Amy, then read you figured it out! daaaah nice one chippo. Maybe I can send it in as an Article for this site. lol.
  7. C

    O2 sensors

    I've got a stock three wire O2 sensor on my 1996 K11 Micra white - black - white Do you know if this is a wideband sensor?
  8. C

    Micra owners with 14" rims - what tyres are you using and where did you get them?

    OK! Here's what I came up with using the Miata.net Tire Size Calculator. http://www.miata.net/garage/tirecalc.html Tyre choices either side of the original Nissan Micra 155/70/13 rolling diameter. 195 50 14 - Speedo will be 0.6% too slow / 100km/h will actually be 100.6km/h 185 50 14 - Speedo...
  9. C

    APEXi vs K&N

    Yeah the kit is a bit pricey at around the AU$250 mark but I havn't got any room up front for the cold air job. With all the air-con and radiator stuff up front. Later on down the track I might remove the battery and set up a air box arrangement. (see picky) Well similar to this picky. You can...
  10. C

    APEXi vs K&N

    Breathe....
  11. C

    APEXi vs K&N

    Not the easiest of installations. But with a bit of perservirence with the 10mm open face spanner, your there.
  12. C

    APEXi vs K&N

    Well... I finnally went with the APEXi kit and here's what it looks like installed.
  13. C

    OK my temp gauge is really low - where should it sit?

    Yeah that's what I thought, every other car I've had sits some way up the guage - thanks for your info guys will get onto this pronto. Hopefully it's just a bad reading.
  14. C

    Micra owners with 14" rims - what tyres are you using and where did you get them?

    I recently just got some 14"x6" CSA mags of a GTiR and I roughly want the same rolling diameter as the 13" steelies, which I guess is about 50 or 55 but what about width? I want it as slim as possible or am I stuck with 185? Is there such thing as a 175/50R14 or 175/55R14?
  15. C

    OK my temp gauge is really low - where should it sit?

    Thanks for that Brendon, mine hardly moves up at all. Only just clears the starting mark. Should be fine then I guess.
  16. C

    Installing Japanese 2000 model bubble rear light clusters on an Australian micra

    Finally sorted out the wiring! Thanks for posting this diagram cisco! I would of been lost otherwise. That little white harness is a tricky piece of work! Took me a while to figure it out. Would be good to post just how to tackle it for anyone new to these. I would but I'm way to busy at the...
  17. C

    OK my temp gauge is really low - where should it sit?

    Like my topic says! um... shouldn't it be sitting somewhere around the 1/3 mark or just under half? Maybe someone took out the thermostat altogether cause the guage does go up, but only a little. Any help much apprieciated!
  18. C

    japan and stuff

    Looks like Something out of M*A*S*H! :)
  19. C

    Installing Japanese 2000 model bubble rear light clusters on an Australian micra

    Do both plugs have to be re-arranged? How are you supposed to get that white plug off its black perch? And exactly how do you use your screwdriver to remove these pins? I tried lifting the obvious, but it wouldn't budge. Had a look at an empty spot as a reference and it looks like something...
  20. C

    APEXi vs K&N

    For those interested in the APEXi kit, here's what it looks like!
Back
Top