Recent content by bazz

ok people,hgk have rung me : good service (Y), and nattered, no visual faults so sent bact to germany for burner rig testing : NO FAULTS, so next is to contact supplier to claim units back. A piece of advise discovered in a trade magazine write up discovered by NGK: you have to replace front...

Hi all, just done a snapon seminar course which showed cut up 02 sensors to see inside and diagrams showing how they work, prior to going into hospital, my supplier aint contacted me yet to say had back, ihave just emailed the manufactuerer to confirm if sensors are good how do they come back...

code read Hi Slug - where you based, do you a free read if you local and can get to me

Hi all, wandering if there is flash code procedure for the K11 Micra Airbag system, got a light on and my code reader shows no codes present: current,past or trouble diag record. Wandering if my software is missing codes etc, any techs out there or has any one flash code read their K11's...

update on sensors Ok,sensors have been returned back to supplier which inturn go back to Germany and will be placed on BURNER RIG to test,if good, i get them back, if faulty i get a full credit,that is the reply direct from NTK part of NGK,not costing my anything... not even postage,will let...

Not sure if should post this, ok my client says to remove new sensor as did not cure and i fitted his old breakers yard unit which is faulty. So going to look at setting up bench test for these 2 NEW NTK (prt no: 0ZA603-N2) sensors i have,cheaper than the dealer £150, if they work fine, i...

Did some internet searching: wideband sensors have 5 or more wires seemingly,the 1 im working with has 4 wires, the guys sensor has a failed heater circuit: so we fitted new,5+ days later we are experiencing runing problems,start her up,let her idle, then after about 1 minute the idle is...

I have to admit, i have not heard of 'wide band sensors', being in the trade, our dealer machine gives us oxy codes we change and all is sorted,this is 1st 1 i have had to do some investigating with, earning a bit of pocket money here and there ;) outside work. New sensor arrived, fitting...

Hi all, showing continous 2.45-2.49 volts either way, wiring diagram shows no continuity for oxy sensor pin 2 to pin 35 ecu (should be) so possibly a wire fault. Gona buy another new sensor and fit and see what happens,also thinking about bridging 3 wires at oxy sensor to ecu and see if this...

Thank you for your views Bombardier, it is appreiated, my new fitted sensor (which may have been supplied faulty) is fitted and showing no voltage,as soon as you crank the engine and it idle's, my sensor voltages according to my scanner are 2.49volts continous, NO ALTERNATING value at all...

Hi all, K12 2006 1.2 engine, engine code p0132, removed and replaced the front sensor Bank 1 Sensor 1, cleared the code and road tested, the light comes back on...... with each road test the light takes longer to come on.... road test 1 - 1mile light on, road test 2 1.5 mile before light came...

Hi,i am working on a K12 at present, i see you commented on SELF LEARN - dont spose you could expand on this and how to go about doing it, i have just replaced B1S1 on a K12 Cheers bazz

Any nissan techs on here, would appreaite some help please,code p0132 - 02 signal high bank 1 sensor 1 NEW SENSOR FITTED.

Thanks for your views, the heated circuit is showing resistance, not sure what spec should be, and on my scanner the sensor shows supply voltages 2.49, when viewed inwave form, it does not appear to be switching on & off. Will let you know how i get on, cheers.

Hi all, new here,look forwards to views and help, return the favour may be one day. K12 56 plate micra 1.2, eng code p0132 B1 S1. I know i can carry out resistance checks across 2 pins in the sensor to check operating range,does any one know wether i can do the same for the micra's...