Search results

  1. C

    N14/N15 final drive compatibility

    RS5F30A exploded view
  2. C

    N14/N15 final drive compatibility

    You need the two final drive gears, one bolts onto the diff, part #143, the other is one piece with the shaft, part #2. See picture below.
  3. C

    N14/N15 final drive compatibility

    K11 RS5F41A are easy to find & cheap in NZ. Yes the shafts are smaller. There were not many K10s imported to NZ, so the final drive is probably best sourced from UK or possibly via your nissan dealer with the following part numbers: RN5F41A FINAL PARTS 1988 Genuine Nissan Parts 38101-01B13...
  4. C

    N14/N15 final drive compatibility

    Only a few rare K11 had the 31, it was the viscous LSD version. 31 boxes from a GA motor will bolt onto a CG. The CD17 & CD20 nissan diesel motors found in the N14/15 also have 31 boxes but most likely the bell housing is like the CA motors, and won't bolt to GA/CG. The diff from these or the...
  5. C

    Body kit

    3
  6. C

    Body kit

    2
  7. C

    Body kit

    http://www.trademe.co.nz/motors/used-cars/nissan/march/auction-394784835.htm
  8. C

    crazy Swedes micra, Rwd

    Inspiring. Can't wait for some in car video
  9. C

    pulsar engine?

    If crazy swede can fit a turbo BMW 6, an RB26 should be no problem...
  10. C

    Wanted Speedo drive for 13v gearbox

    Easiest source in NZ is from a CG16DE powered N13 Pulsar
  11. C

    Differences in distributor?

    5 sockets probably means there is an external coil? So find the coil wires that normally connect internally & run them to the external coil. Job done?
  12. C

    raising my oil pressure...

    In NZ climate, I always use 20-40 or 20-50 in higher km engines to reduce rattle when cold. Using 10-50 in a 200,000+ km engine will most surely rattle badly & take another second to reach pressure from startup.
  13. C

    Differences in distributor?

    There are at least 3 different distributors on earlier JDM K11, using at least two different plugs. They all fit in the head the same, but you might have some wiring to do.
  14. C

    need advice on drive shaft play

    You don't just torque it up. Depending on the brand of CV there will either be a pressed metal cap that goes over the nut that is then held in place with a split pin, or the split pin will engage directly with the nut, or the will be a groove in the CV shaft that a thin part of the top of the...
  15. C

    K13 Differences in the world

    K13 is produced in several different factories to various spec levels. Australian & NZ K13 Micra come from Thailand. Different countries have different expectations, hence CVT's in Japan, manual gearboxes available for Europe/Australia, small engines in India, bigger engines in Australia/NZ...
  16. C

    **Mystery Rattle. Drives me bonkers!!!**

    I had a rattle coming from a similar direction in a 2dr Starlet I once owned, there was a large panel beating dolly left inside the panel/sill between the door & rear wheel.
  17. C

    K13

    So who is going to be the first to fit the 140kW MR16DDT or when will Nissan put it into production? The front drive CVT MR16DDT Juke weighs 1290kg. http://www.carview.co.jp/catalog/NISSAN/JUKE/2010/spec/41332/ The 4WD CVT version weighs 1380kg...
  18. C

    K13

    NZ$22,600 x 0.77 = AU$17,402 This is for a 1.5L auto. The article from the first post above lists the cheapest K13 as AU$12,990 and then says AU$13,990 drive away. From this I take it there are about $1000 on road costs in Australia, so the price for the 1.5L auto would be...
  19. C

    DOES THE MICRA SHARE WHEEL BEARINGS OR HUBS WITH ANY OTHER NISSAN PLATFORMS?

    With the JDM K11 there are at least two different hub sizes, I'd suspect the smaller is the same as K10 & the larger may be the same as GA13 powered N14. The K12 may have similarities with 1.5L Tiida, and of course with the Renault Clio with the same floorpan? The K13 in future will have...
  20. C

    K13

    http://www.nissan.co.nz/passenger/micra/index.php
Back
Top