You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser.
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
Ordered a pair of NTN 4T-30208 bearings for the LSD diff and a SKF 6305/C3 to fix the rattling old input shaft bearing
Visited Jack...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
Gave Jack a lift down to Whitby today where he's buying another Micra 😁
Kassandra drives alot smoother now without the old annoying...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
2024-03-27 Replace Rear Speakers
For the past few months the rear right exposed speaker must have got some debris stuck inside the coil...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
Removed the old single gas-strut
The old ball-joint sat too low at 15mm, making the strut rub against the chassis top.
It needed...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
2024-03-26 Lathe Ball-Turning Jig
I wanted to fit a 2nd bonnet gas-strut but thought I didn't have any spare ball-joints, so decided to...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
printed this simple bracket for mounting the wideband gauge under the dash neater rather than screwed to the bottom corner
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
today only had enough juice to polish the exhaust tip
and begin removing stickers off the boot for a cleaner look
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
2024-03-23 Flat Bottom Drill Bit
The next tool to make in prep for machining the LSD cover plate is a 6mm - 12mm flat bottom drill bit...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
today went for a brief cars & coffee meet up with some m8s
back at home I cleaned up the white oxide off the dizzy cap, hopefully...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
2024-03-19 Machine New Cover Plate for Gripper LSD
The Gripper LSD had a broken cover plate 5yrs ago...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
2024-03-17 Window Glass Clips
Recently noticed one of the window clips had come off 🫣
Ever since I replaced the electric window motor...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
2024-03-16 Inside a Fuel Tank
Curious to look inside the old tank since I'll be binning it, took awhile to cut through cos it's made...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
2024-03-14 Insurance Drama, Mental Illness
I rang Adrian Flux for a renewal quote and was jaw dropped when quoted over £750 fully comp...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
2024-03-15 Inspecting Fuel Tank Components
While feeling sad I decided to dismantle some old parts to see how they work.
Pre-face fuel...
-
A
andy reacted to
pollyp's post in the thread
PollyMobiles Rebuild with
Like.
2024-03-09 Swap Pre-face Fuel Tank with Face-lift Fuel Tank
Since 2012 I've been running a Walbro 255lph pump in a pre-face fuel tank...