Home
Forums
New posts
Search forums
Model-by-Model
K10
K10 General Discussion
K10 Micra Blogs
K10 Tuning & Mechanical
K10 Bodywork & Interior
March Superturbo (EK10) Forum
Nissan Pao (PK10) Forum
Nissan Figaro (FK10) Forum
Nissan BE-1 (BK10) Forum
K11
K11 General Discussion
K11 Micra Blogs
K11 Tuning & Mechanical
K11 Forced Induction tuning forum
K11 Bodywork & Interior
K11s in Motorsport
March Cabriolet (FHK11)
K12
K12 General Discussion
K12 Micra Blogs
K12 Tuning & Mechanical
K12 Bodywork & Interior
K13
K13 General Discussion
K13 Micra Blogs
K13 Tuning & Mechanical
K13 Bodywork & Interior
K14
K14 General Discussion
Stickers
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Please only use these forums for blogs, they are
not
a discussion forum
Home
Forums
Build Diaries
K11 Micra Blogs
PollyMobiles Rebuild
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="pollyp" data-source="post: 794173" data-attributes="member: 4527"><p>a m8 Daniel needed a meth injection kit fitted onto his audi TT.</p><p>the most logical place to fit the nozzle is this plastic pipe between the intercooler and TB but removing all the difficult clips & fasteners was a PITA</p><p></p><p>[ATTACH=full]75379[/ATTACH]</p><p></p><p>this was the only flat surface for screwing the BPST nozzle onto and clear the cooling fans</p><p></p><p>[ATTACH=full]75380[/ATTACH][ATTACH=full]75381[/ATTACH]</p><p></p><p>attached the solenoid to the airbox tray</p><p></p><p>[ATTACH=full]75382[/ATTACH]</p><p></p><p>mounted the reservoir & pump in the boot</p><p></p><p>[ATTACH=full]75383[/ATTACH]</p><p></p><p>the hardest part was figuring how to route the pipe & wiring neatly through the car.</p><p>there's no easy access gromet holes in the footwell or bulkhead,</p><p>routing past the door seals looks ugly and will crush the pipe/wires,</p><p>the engine loom goes up inside the scuttle panel & deep into the dash but the wiper arms are seized onto the spindles ?</p><p></p><p>took a lot longer than expected, as usual, so we'll have to wait another week to buy a wiper puller tool, wire it up & calibrate the pressure sensor ?</p></blockquote><p></p>
[QUOTE="pollyp, post: 794173, member: 4527"] a m8 Daniel needed a meth injection kit fitted onto his audi TT. the most logical place to fit the nozzle is this plastic pipe between the intercooler and TB but removing all the difficult clips & fasteners was a PITA [ATTACH type="full"]75379[/ATTACH] this was the only flat surface for screwing the BPST nozzle onto and clear the cooling fans [ATTACH type="full"]75380[/ATTACH][ATTACH type="full"]75381[/ATTACH] attached the solenoid to the airbox tray [ATTACH type="full"]75382[/ATTACH] mounted the reservoir & pump in the boot [ATTACH type="full"]75383[/ATTACH] the hardest part was figuring how to route the pipe & wiring neatly through the car. there's no easy access gromet holes in the footwell or bulkhead, routing past the door seals looks ugly and will crush the pipe/wires, the engine loom goes up inside the scuttle panel & deep into the dash but the wiper arms are seized onto the spindles ? took a lot longer than expected, as usual, so we'll have to wait another week to buy a wiper puller tool, wire it up & calibrate the pressure sensor ? [/QUOTE]
Verification
Post reply
Home
Forums
Build Diaries
K11 Micra Blogs
PollyMobiles Rebuild
Top