• Please only use these forums for blogs, they are not a discussion forum

PollyMobiles Rebuild

2021-05-09
washed up for sundays meet in darlington & stockton

IMG_20210509_154418.jpg
IMG_20210509_154520.jpg
IMG_20210509_181749.jpg
 
2021-05-10

the exhaust often felt kinda choked at high end with the 2nd cat in place for last years MOT, so it's time to resort back to de-cat.
but first one of the v-band flange needed swapping around

IMG_20210510_192230.jpg


I cut the female flange off the downpipe

IMG_20210510_193735.jpg


grinded the old weld down

IMG_20210510_194959.jpg


welded the new male end on

IMG_20210510_195022.jpg
IMG_20210510_200051.jpg


and then I could make the new stainless de-cat pipe

IMG_20210510_212503.jpg
IMG_20210510_213008.jpg


now with only the primary manifold cat in place, the mid & high end feels slightly faster
 
2021-05-11

for the last few months my mini lathe seems like it's shocking/tingling me whenever it's powered and my hands brush against any steel surfaces ?⚡

time for a well overdue clean up

IMG_20210511_200244.jpg
IMG_20210511_202534.jpg


and yup looks like all the swarf had gone into the motor and causing a slight short from the live parts to the casing to the steel frame

IMG_20210511_202540.jpg
IMG_20210511_204243.jpg


after clearing the swarf it's no longer as shocking ?
 
2021-05-12

another gr8 busy wednesday car meet on a warm sunny evening this time ?

IMG_20210512_184334.jpg
IMG_20210512_184344.jpg


later on I discovered someone with a clean 02 1.4 facelift, preface superS front end, march style boot lid, gizfab bits, BC BR coilovers ?

IMG_20210512_204650.jpg
IMG_20210512_204714.jpg
IMG_20210512_203431.jpg
IMG_20210512_203320.jpg


me m8s frankie & zara also found a good gathering of their red MX5's ?

IMG_20210512_194851.jpg
IMG_20210512_202304.jpg
IMG_20210512_202211.jpg
 
the cheap £6-8 Dunlop FP-M12C tie-rod ends don't last long (only 1yr) and the one I replaced recently was defective and already too sloppy ?

so I brought these more pricey £16 XFRM12 joints which has previously lasted 2+yrs

IMG_20210512_215955.jpg


cut & machined the threaded part off some spare old tie-rods to weld onto the short rod-ends

IMG_20210513_200011.jpg


realised they have m12x1.75 threads so I had to retap them to m12x1.25

IMG_20210513_200654.jpg


so I can join em with a spare tie-rod for welding

IMG_20210513_201956.jpg
IMG_20210513_210154.jpg
 
the slower TIG welding puts soo much heat into the metal so I had to weld 10mm at a time immediately followed by quenching in water so the heat doesn't damage the teflon lining and then do a rapid pulsed final pass to even out the surface finish

IMG_20210514_200805.jpg


removed the old worn cheap rod-end

IMG_20210514_213237.jpg


double checking the clearances of the new joint

IMG_20210514_214359.jpg


added the dust boot to the new joint

IMG_20210514_215811.jpg


realign & test drive it tomorrow
 
assessing the old worn tie-rods, the spherical ball is quite corroded with heavy deposits of the teflon lining

IMG_20210515_123052.jpg


cutting it apart and I'm surprised to see that the cheap rod-ends consists of a separate spherical bearing pressed into a thin-walled tie-rod housing. so during a trackday, all the steering tension forces is going through a 2mm thick ring ?

IMG_20210515_124050.jpg


inside is a brass mesh coated in teflon? which has clearly worn through and deposited onto the polished sphere over a short time

IMG_20210515_124141.jpg


I wasn't happy with only 15mm of thread engaging :oops:

IMG_20210516_143825.jpg


so I welded an extra piece of threaded end to lengthen the tie-rod end

IMG_20210516_150800.jpg


applied an updated CCS sticker with new letters

IMG_20210516_162415.jpg
IMG_20210516_162427.jpg
 
on sunday the CCS club had a convoy trip from a rainy teesside park going upto a sunny scenic Clay Bank park

IMG_20210516_223844.jpg
IMG_20210516_223917.jpg


with no idea where we were all going, following behind each car was quite stressful whenever we get stuck at the red lights and having to rush to catch back up ?

IMG_20210516_181341.jpg
IMG_20210516_224101.jpg
IMG_20210516_224331.jpg
IMG_20210516_224728.jpg
IMG_20210516_224901.jpg


the next destination at Saltburn was abit easier when I overhead the postcode to plot onto my satnav beforehand.

IMG_20210516_225647.jpg
 
the bathroom tap has been leaking for a few yrs, so i tried to unscrew & pull it apart only to end up snapping the rusty parts off ??

IMG_20210517_195824.jpg


when a 5min job turned into a "Oh crap it might be a big repair job" ?
there's lots of corrosion and small bits to maybe TIG weld?

IMG_20210517_194639.jpg


checking my spares plumbing toolbox I discovered this used valve from the kitchen tap is compatible with the bathroom tap housing

IMG_20210517_200050.jpg


and it worked. saved hours of work and no longer leaks ?

IMG_20210517_203604.jpg
 
Man balances pool cue on forehead for 2 hours, 16 minutes

That's was a Interesting news
But I want to tell you something important
I am sure you heard about Palestine and isreal ?
You know I did research then I found Israel is a terrorist country
They are killing innocent people in Palestine
We should stand and boycott Israel and those who are supporting Israel

You know I can't hate them just becouse they are Muslim
We should show we have a soft heart and we love humanity
I am sure if you are a not a terrorist or hater
Then you will agree with me

#support Palestine
#boycott Israel


Sent from my TECNO KC2 using Tapatalk
where is the fxxxing mods and admin on this site, this is spam, ya need to up ya game a bit lads and lasses
 
m8 Daniels new carbon spoiler wasnt sitting flush to the boot due to the petruding screw head underneath the base panel

IMG_20210522_150928.jpg


so I carefully countersunk the cheap ebay fiberglass base panel holes to make the screws sit flush

IMG_20210522_123945.jpg


ran out of sealant so I applied some foam tape

IMG_20210522_132542.jpg


cleaned the old gunk off the boot too

IMG_20210522_151000.jpg


sits slightly better on the boot lid

IMG_20210522_151013.jpg
 
peeled off the temporary 'electrical tape' sun strip but looks like the sun had cooked the glue onto the glass ?

IMG_20210522_181302.jpg


cleaned the glue off the glass after a lot of messy rubbing with acetone

IMG_20210522_185025.jpg


applied the new new vinyl sun strip to align with the horizon

IMG_20210522_191353.jpg
IMG_20210522_191415.jpg


gave her a wash for tomorrows cruise & car meet

IMG_20210522_195412.jpg
IMG_20210522_200728.jpg
 
had this spare dash cam with a small lightweight reversing camera, which is perfect for filming my front tyre flexing under load.
the CCD inside was wonky by 6deg so I printed this mount which holds it angled on the end of a threaded rod

IMG_20210523_151258.jpg


rod is bolted to the tow bracket and is at the perfect angle. can't wait to test it on a dry day

IMG_20210523_152530.jpg
 
went for a run after sunset and it worked ok

IMG_20210524_210836.jpg
IMG_20210524_210912.jpg


the long rod zip tied to the bumper obviously vibrates with the engine at low rpm but is fine at high speeds, so I may use a lighter/hollow/big diameter tube to reduce movement.

the dash cam captured the interior shot & tyre cam in 'meh' quality but the highly inefficient file system was a pain to process.
it records each camera in 5min segments, each being 700mb and each had to be slowly converted from MOV into MP4 for the PC editor to import (otherwise it crashes) ?

 
got myself a compact digital oscilliscope which will come handy for electrical diagnosis.
plus a new 17mm impact socket cos the 17mm in my impact socket set was seriously made wonky and would wobble badly

IMG_20210527_175027.jpg


and now this new 17mm spins perfectly centered ?

IMG_20210527_180204.jpg


decided to paint a subtle red lip around the white wheels to divide/transition between the bright white and grey/black tyres ?

IMG_20210527_193138.jpg
IMG_20210527_193154.jpg
IMG_20210527_193212.jpg
 
replaced the terribly rusty old bonnet with the spare blue one

IMG_20210530_105156.jpg


kinda looks alright & shinier but really does highlight just how wonky her entire front end is too cos nothing lines up well to the bonnet ? ?

IMG_20210530_132405.jpg
IMG_20210530_132514.jpg
 
ducktaped this perspex to the tyre camera mount in an attempt to stiffen support & reduce shaking.
if anything it actually made it shake even more lol

IMG_20210531_132833.jpg


good thing the shakey footage is downsized smaller compared to the stable HD GoPro camera.
went for another sunny weekend drive to test it out ?

 
Daniel wanted an Odyssey gel battery fitted to his Audi TT turbo, so I removed the big old heavy battery

IMG_20210603_184321.jpg


drilled & bolted the battery enclosure onto the car

IMG_20210603_185306.jpg


reattached the battery cables

IMG_20210603_190040.jpg
 
Michael Stanhope needed a hoop making for hanging his steering wheel off the roll cage, so with a few dimensions I modelled this up

Rollcage Steering Hook 1b.jpg


and printed it off

IMG_20210603_211108.jpg
IMG_20210604_003500.jpg


good results. hope it works well for him :cool:

IMG_20210605_193812.jpg
IMG_20210605_193834.jpg
 
took a covid self test on thursday, eeeks its like shuving a tickly feather down my throat & nose, made me gag & sneeze :sick:? but at least it was negative :)

IMG_20210603_232009.jpg


Friday the next day after work I drove all way up to Hexham to get me 1st Pfizer jab.
overall it was a pleasant experience, friendly ppl, honestly the needle was sooo tiny I didn't even feel it.

18:30 I had the jab

21:00 the muscle around the jab area was only slightly beginning to ache a bit

09:00 Saturday next morning the jab area was still slightly aching and had a dull tension headache, but that was normal for me on weekends which was fixed with ibuprofen

Sunday I was all fine (y)
 
over the weekend I went to get a whole load of grey paint, white etch primer & laquer and decided to strip apart all her doors to fix all the rust

IMG_20210605_215742.jpg


to remove the rear door window, I lower the window & unbolt the metal divider

IMG_20210605_151352.jpg
IMG_20210605_150440.jpg


the rear 1/4 glass simply swings off

IMG_20210605_150458.jpg


it sat in this groove

IMG_20210605_150515.jpg
IMG_20210605_150405.jpg


I quite like this pillar-less look :cool:
since I never use the rear windows, I think I'll just tigerseal some perspex over it instead

IMG_20210605_153712.jpg


removing the window reveals all the rust holes ?

IMG_20210605_150424.jpg


rust #1 on the right door

IMG_20210605_211204.jpg
IMG_20210606_170410.jpg
IMG_20210606_171552.jpg


rust #2 on the right door

IMG_20210605_211213.jpg
IMG_20210606_170418.jpg
IMG_20210606_171600.jpg


this one's the worst on the right door

IMG_20210605_154722.jpg
IMG_20210605_154738.jpg
IMG_20210605_211223.jpg
IMG_20210606_170426.jpg


rust #4 on the left door

IMG_20210606_170439.jpg
IMG_20210606_171643.jpg


finally the front passenger door had bubbling rust

IMG_20210606_173945.jpg
 
Daniel in his Audi TT turbo needed a stainless intake pipe making, so here's the original plumbing with the black plastic elbow pipe leading from the MAF down to the turbo inlet

IMG_20210606_121620.jpg


gathered all the stainless materials

IMG_20210606_123635.jpg


trimmed & tacked the pipes together

IMG_20210606_141820.jpg


drilled hole for the breather port

IMG_20210606_152440.jpg


the original pipe had this sharp bend near the turbo inlet whereas the new stainless pipe has a smooth gentle bend

IMG_20210606_153521.jpg


bolted up neatly and looks gr8. he said it spooled up slightly sooner too which is good news ?(y)

IMG_20210606_154504.jpg
IMG_20210606_154704.jpg
IMG_20210606_155150.jpg
 
Making the rear window one piece is pretty smart, quite like the symmetry of that and the front windows if you decide to do it
 
removed all the doors, wings, bonnet, bumpers so that I can wirebrush & rattle can the rear wheel arch, scuttle panel & sills.

then repair the doors & sand all the panels down in preparation to take them all over to Luke on saturday to respray them properly with his spray gun & 500ml tin of base coat

IMG_20210607_194338.jpg
IMG_20210607_194356.jpg
IMG_20210607_194317.jpg
 
welded & smoothed the rear offside door rust patches

IMG_20210609_203524.jpg
IMG_20210609_222202.jpg
IMG_20210609_222220.jpg


for the lower corner, welded the vertical backing plate 1st

IMG_20210609_205923.jpg


and then weld & smooth the curved edge

IMG_20210609_215955.jpg
IMG_20210609_222149.jpg


weld & smoothed the rear nearside door

IMG_20210610_184022.jpg
IMG_20210610_184749.jpg


time to fully strip apart the doors, wirebrush & treat & bodyfill the rust patches

IMG_20210610_205631.jpg
IMG_20210610_200917.jpg


on the nearside door this is where the water drain got under the seam sealer and started bubbling the inside & outside edge

IMG_20210610_194518.jpg


slightly bubbling around the rear drain hole

IMG_20210610_194529.jpg


stripping the drivers door

IMG_20210610_202347.jpg


the rubber strip was oddly glued to the door here, which of course torn it :rolleyes:

IMG_20210610_202403.jpg


once again the bloody seam sealer just trapping moisture on both drivers side doors till it rusts

IMG_20210610_202421.jpg
IMG_20210610_204522.jpg
IMG_20210610_204548.jpg


the rear door also having the same rusty seam sealer

IMG_20210610_213550.jpg
IMG_20210610_213517.jpg


going to a labour intensive delivery job 9-5 followed immediately by these long nights stripping & repairing kassandras rust in a rush to make the yorkshire modified show on 20th june is beginning to strain my body stamina & mind ??

dunno if I'll have the energy to get it all done in time or collapse or simply throw the towel ?‍♂️
 
I had 500ml tin of base coat plus 4 spraycans but felt this wasn't enough for all the doors & big bonnet & wings,

so this early saturday morning the plan was to go order another 1L of base coat to be sure I had enough, return home to further sand the bonnet & wings before luke arrives on afternoon with his compressor.

that plan was ruined when the store was very busy and had a 2hr waiting list!
so I wasted some time buying an orbital sander to aid sanding the big panels & go for lunch, collected the 1L of paint at 12pm and got home for 1pm where luke just arrived

IMG_20210612_114259.jpg


this was gonna be a huge task which was stressing my tired head. while luke paints the doors & bonnet with the 1.5L of paint (which was thankfully enough) I prepped the bonnet with the new sander

IMG_20210612_130451.jpg
IMG_20210612_144734.jpg


it was a very messy job with paint fumes & dust going everywhere and very limited space to carefully hang the freshly painted panels :unsure:

IMG_20210612_150000.jpg
IMG_20210612_153654.jpg


the painting was ok, wasn't perfect and a few flies trapped in the layers but it'll do

IMG_20210612_165618.jpg
IMG_20210612_174833.jpg


he told me it takes days to fully harden before any buffing so I gotta store em round the house carefully ?

the rest of the rusty wings, rear 1/4 and both bumpers I'd have to rattle can em myself.
so I bodyfilled the rear arch, but the cheap stuff I got from work was absolute pigsheet, didn't mix proper or harden, so I gotta brush it off tomorrow, get the proper p38 and start again ?

IMG_20210612_211458.jpg


the 1x1m of polycarb sheet arrived for covering the rear door

IMG_20210611_180733.jpg
 
the cheap bodyfiller I brought from work was definately old & dried up cos the filler was actually thick like scooping frozen ice cream and very difficult to mix properly.

so this morning I brought some fresh P38 from halfords and wow huge difference. it's much softer like honey and a lot easier to mix thoroughly.

now I can body fill & sand down the rear 1/4

IMG_20210613_124256.jpg
IMG_20210613_124310.jpg


masking

IMG_20210613_134345.jpg


on this hot day, I began spraying with what I assumed was white etching primer that the paint shop gave me.
but to my horror it immediately started cracking apart as it dried, looking like a desert floor ?

the hell !!
I tried sanding it off, which was tricky cos it kept clogging the sand paper ?

degreased it with brake cleaner and tried again with the white primer, only to happen once again ????
FFS

was talkin to Luke about it only to realise the can said it was High-Build white etch primer which wasn't suited for the hot temps and needed thinner layers.

IMG_20210613_144858.jpg


well, I'm fuming, frustrated I messed up, I don't have time to slowly sand this mess down to respray with normal primer, so I just carried on spraying basecoat over this wrinkly mess and it's an eye sore ?

IMG_20210613_165553.jpg
IMG_20210613_165615.jpg
IMG_20210613_165632.jpg


nothing I can do bout it yet cos I have a show on Sunday, but I'll respray it with normal primer soon afterwards.

wirebrushed & treated the rusty front wings

IMG_20210613_134334.jpg


smoothed bodyfiller.
the new orbital sander I brought yesterday makes the job of flattening the bulk of the excess bodyfiller a lot easier & faster compared to previously doing it all manually by hand ?

IMG_20210613_165652.jpg


sprayed it with normal halfords grey primer and it looks a lot better & smoother than the rear 1/4 mess

IMG_20210613_175642.jpg


sprayed 500ml cans of base coat & lacquer per panel and the result is nice ?
all the wobbly inperfect sanding is obvious with a glossy finish now but at least it's no longer rusty ?

IMG_20210613_182151.jpg
IMG_20210613_183641.jpg
IMG_20210613_194815.jpg


to end the long day, all 4 doors were bolted back on

IMG_20210613_221329.jpg


it's taken a full exhausting week to strip, repair & paint all the major body panels ?
half way there and now I'm on the home stretch,
reassembling everything over the next 5 days,
make a new polycarbonate rear door window,
clean all the dust out of every friggin surface of the car,
then polish all the nasty orange peel off the new paint ready for sundays show ?
 
Polly, I would have rather you stayed focused on a slow job and skip the deadline. Maybe just go with a mate next time a deadline approaches? I've stopped with the crazy deadlines now, and my life is much more balanced!
 
Polly, I would have rather you stayed focused on a slow job and skip the deadline. Maybe just go with a mate next time a deadline approaches? I've stopped with the crazy deadlines now, and my life is much more balanced!

I already paid for and commited to going to the show, chosing to fix this rust 2weeks ahead but as usual the job always ends up bigger than expected.

was determined to do whats neccessary to get the car ready for the big show (maybe only show of the year if covid gets any worse) even if I'd have to push my body hard.
 
The black underbonnet is pretty smart, like that - is it a satin?

Re the polycarb windows - how is the 3mm - is it rigid enough? I measured my Humphris set - they're 4mm which is (relatively) a fair bit thicker?

Craig
 
The black underbonnet is pretty smart, like that - is it a satin?

Re the polycarb windows - how is the 3mm - is it rigid enough? I measured my Humphris set - they're 4mm which is (relatively) a fair bit thicker?

Craig

it's halfords matt black

the 3mm seems stiff enough but as I'll write about further down, I should've heated & curved it to relieve stress cos it peeled the tigerseal off the door frame
 
Polycarbonate Rear Door Window

made a cardboard template of the rear door window

IMG_20210616_222540b.jpg


carefully jigsawed & trimmed the polycarbonate sheet

IMG_20210617_185743.jpg
IMG_20210617_195250.jpg
IMG_20210617_202143.jpg


clamping the sheet to the door within a small garage was near impossible so I removed both doors to clamp em separately

IMG_20210617_210808.jpg


apply a thick bead of tigerseal

IMG_20210617_214521.jpg


I simply couldn't get enough clamps to hold this flat straight sheet against the curved door frame

IMG_20210617_222111.jpg


but disaster!
after removing the clamps for a day, the polycarb sheet on the rear offside door had cleanly peeled straight off ?
it seems that the halfords lacquer wasn't actually fully cured so the solvent reacted with tigerseal preventing it from bonding/curing to the painted door frame ?

IMG_20210618_173928.jpg


the nearside door which Luke painted with 2k lacquer from his spray gun had fully cured so the tigerseal had no problem curing & bonding the sheet to the door frame...

except I didn't apply enough sealant at the corners, leaving many huge leaky gaps ??‍♂️?‍♂️

IMG_20210618_174428.jpg
IMG_20210618_174456.jpg
IMG_20210618_174521.jpg
IMG_20210618_174551.jpg


so I abandoned this idea and bashed/peeled the window off the door frame.
maybe in future I'll heat/curve it to the door, apply a thicker bead & rivet it on too.

IMG_20210618_175241.jpg


wirebrushed the tigerseal off the door

IMG_20210618_203918.jpg


reinstalled the windows

IMG_20210618_214152.jpg
IMG_20210618_224704.jpg
 
Last edited:
with 1 day to go till Yorkshire Modified Show and waiting 1 week for the paint to harden,
it's time to visit Luke to help polish all the orange peel off the new paintwork on this hot day

IMG_20210619_111124.jpg
IMG_20210619_111137.jpg
IMG_20210619_111151.jpg
IMG_20210619_111216.jpg


soon realised we only had 1200grit paper and buffing compound but no polish :rolleyes:
so a lot of the afternoon was wasted on waiting for ppl to bring some 3000grit paper and polish

IMG_20210619_132841.jpg


lukes corrado bumper need some cooling holes cut out & welded

IMG_20210619_135335.jpg


it took all afternoon for luke to just polish the bonnet enough but at 6pm soon ran out of time as the family & neighbours complained ?

IMG_20210619_174227.jpg


things got worse as he jet washed the passenger door and a whole sheet of lacquer was ripped clean off by the HP jet! ?
I feared that it exposed bare basecoat but its shiny ?

it seems that since he sprayed halfords aerosol lacquer on top of quickly cured 2k lacquer (cos he ran out), it didn't bond well at all and simply peeled off like cling-film ?‍♂️

IMG_20210619_174243.jpg


so with time running out, I had to drive a half sanded car back home to finish buffing the remaining panels throughout a long night ?

IMG_20210619_181811.jpg
IMG_20210619_191704.jpg


I did a single pass of G3 compound and quickly ran out of steam and just had enough, it'll do

IMG_20210619_201449.jpg
IMG_20210619_210728.jpg
IMG_20210619_210744.jpg
IMG_20210619_210827.jpg
IMG_20210619_210858.jpg
 
20-06-2021 Yorkshire Modified Show

The early morning of Yorkshire Modified Show started off rather wet, worrying it was gonna be a muddy soggy grass field.
We began on a nice long convoy through the yorkshire moors towards Malton ??

IMG_20210620_072508.jpg


at the show it stopped raining and quickly got warm, sunny, humid ?

it was a gr8 show with soooo many nice cars to see

IMG_20210620_091702.jpg
IMG_20210620_115337.jpg


the highlight of the day was participating in this grass autotest where anyone can drive their cars (including a caravan, limosine, vans) through a slalom course for just a £! :D??

my 1st run was a rusty 46s struggling to see the cones while reversing whereas my 2nd run was a quicker 39s, although touching a cone made it 49s but overall it was amazingly cheap fun!



at the end of the show we just had to go park near the pond for a compulsary beauty photos ??

IMG_20210620_162951.jpg
IMG_20210620_163119.jpg
IMG_20210620_163153.jpg
IMG_20210620_163255.jpg
 
Last edited:
I wasn't happy with the massively orange peeled doors and the badly crackled primer on the rear 1/4

so initially I tried sanding down the orange peel, hoping to polish it flat, but instead it exposed more & more spots of white primer. it was simply too rough when luke sprayed it from his compressor ?

so that was basically a wasted £200 paint job ?‍♂️
and now I decided to sand it ALL flat including the dimples & dents etc and respray it myself this time with another £200 of cans

IMG_20210623_203507.jpg
IMG_20210623_205820.jpg
IMG_20210624_194220.jpg


wiped with brake cleaner and tested some halfords grey primer on the edges...only to watch it fecking crack apart just like the white etch primer!

arghhhh I was soo angry frustrated, why is it doing this! :mad:

oddly it only cracks where I've previously sprayed the white etch primer ?
so after speaking to a paint friend it seems I sprayed too much on the 1st pass (making it skin, shrink & tear whilst the inside layer was still curing)
and the white high build etching plastic primer is mainly for bare metal and could be reacting with fresh paint on top.

IMG_20210624_225051.jpg


to eliminate that reaction, I spent hours sanding ALL of that horrible etch primer off the rear 1/4 till I expose the factory base coat

IMG_20210625_221542.jpg
IMG_20210625_221602.jpg


but from all that sanding I ended up sanding some of my fingers till it bled ??
oopsy that's gonna sting tomorrow ?

IMG_20210625_220947.jpg
 
now ya found the problem paul, am sure it will be right this time (y) "paint society" on youtube, great tips and videos, wanna see the results he gets from a can, although its an American show, principle is the same, is it not...
shes looking good fella (y) get a plaster on it and crack on :ROFLMAO::ROFLMAO::p
 
now ya found the problem paul, am sure it will be right this time (y) "paint society" on youtube, great tips and videos, wanna see the results he gets from a can, although its an American show, principle is the same, is it not...
shes looking good fella (y) get a plaster on it and crack on :p
Hoping it goes right this time, brought a ton of primer, paint, lacquer & 5l of pre prep
Wish this damn weather makes its mind up, its kinda misty/rainy

Finger ain't feeling too bad now but got my Mary golds on now

Sent from my CLT-L29 using Micra Sports Club mobile app
 
after advise from Shaun last night,
I dry sanded the surface,
carefully cleaned it with pre-prep,
patiently started off with very light dusting of primer,
waiting 15min,
wipe any dust with tack cloth,
spray another light coat,
repeat few times till it's solid and then give a final thick even coat using the reflection of a lamp to ensure a consistant coating

and it's worked this time, no more cracking or fisheye etc

IMG_20210626_163310.jpg
IMG_20210626_165402.jpg
IMG_20210626_171229.jpg
IMG_20210626_184215.jpg


did the same on the nearside with same good result

IMG_20210626_163320.jpg
IMG_20210626_171241.jpg
IMG_20210626_184241.jpg


unfortunately there was a bad squishy bubble here, which I had to scrape off, sand down and build a few thick layers.
I hope it cures fully and can be sanded smooth before the base coat ?

IMG_20210626_195925.jpg


painted the passenger door in the workshop since the weather is unpredictable. once again starting with light dusting working towards a thicker 2 coats

IMG_20210626_213243.jpg
IMG_20210626_215650.jpg
IMG_20210626_221820.jpg


there's still 3 more doors to prep, prime, paint and lacquer over the next few days
 
it's halfords matt black

the 3mm seems stiff enough but as I'll write about further down, I should've heated & curved it to relieve stress cos it peeled the tigerseal off the door frame
Nice, looks good.

Yeah, I think a combination of heating in a bit of a curve and some physical fastening should do the trick

Craig
 
built up a thick layer of primer over the hollow bubble last night, sanded it smooth and painted this morning

IMG_20210627_160427.jpg
IMG_20210627_162336.jpg
IMG_20210627_182812.jpg


sprayed 2 coats of base coat using 2 whole cans :oops:

IMG_20210627_182728.jpg
IMG_20210627_182803.jpg


and 2 coats of lacquer :cool:

IMG_20210627_205008.jpg
 
27-06-2021 BC Racing BR Coilovers

Big thanks to Mark aka bushmonkey in the forum for selling his unopened BC BR coilovers. My current BC V1 were getting 11yrs old too, so I obvously just had to immediately go for an impulse purchase a nice chap to talk to

I'm a happy boy tday with shiny car parts :love:

IMG_20210627_195727.jpg
IMG_20210627_195811.jpg
IMG_20210627_195826.jpg
IMG_20210627_200044.jpg


phwoaa ?

IMG_20210627_201214.jpg
IMG_20210711_232802.jpg


here's a link to when I brought my BC V1 coilovers for comparison
https://www.micra.org.uk/threads/pollymobiles-rebuild.35251/post-422090

.jpg


same pillowball camber adjustable top as the V1 except the adjustment dial is secured with a spanner rather than a knurled sleeve.

front dampers came set at 25/33 clicks (76% hard)
rear dampers set at 22/32 clicks (69% hard)

IMG_20210627_202509.jpg


the BR series feature bearing spring top platform so that as I steer lock 2 lock or the spring naturally twists whilst compressing, it'll move freely.

whereas on the solid fixed platform of the V1, the spring would either violently skip around the platform as I steer, or bind/resist steering, or force the whole assembly to swivel the pillowball, which wears out the spherical bearing prematurely.

so the BR pillowball should last abit longer

IMG_20210627_202459.jpg
IMG_20210711_232900.jpg
IMG_20210711_232955.jpg


the locking rings are a nicely casted & radiused alloy.

IMG_20210627_201544.jpg
IMG_20210711_233022.jpg


notice the lower locking ring has a wider, flared wedging contact face, which should help it stay locked more securely

IMG_20210711_233214.jpg


made on July 2018

IMG_20210627_202602.jpg


front comes with 5kg springs

IMG_20210627_201528.jpg


I believe these damper markings are
T: oil threshold temp 226C
C: oil capacity 80ml

IMG_20210627_202349.jpg


the other side has a higher 245C temperature threshold for some reason?

the V1 in comparison has a smaller 70ml capacity and 212C oil temp threshold

IMG_20210627_202427.jpg


rear springs are 4kg and straight tapered

IMG_20210627_201428.jpg


nicely casted locking rings

IMG_20210627_201450.jpg


much sturdier rear damper mount

IMG_20210627_201321.jpg


rear damper specs:
oil threshold temperature 135c (V1 was just 93c)
oil capacity 56ml (V1 was 43ml)

IMG_20210627_201559.jpg


Stickers!

IMG_20210627_195950.jpg


usual front & rear locking ring collar spanners, allen key & rear adjuster dials

IMG_20210627_200238.jpg


look forward to installing & setting these up
 
Last edited:
Back
Top