• Please only use these forums for blogs, they are not a discussion forum

PollyMobiles Rebuild

the last thing to mod at the rear end is to mount the exhaust silencer on rubber mounts to stop it rattling cos it was previously bolted solidly to the chassis beam which made it rattle

IMG_20200419_161814.jpg


I marked in white where the exhaust CoG is to locate one of the mounts to keep it balanced

IMG_20200419_160110.jpg


I wasn't a fan of the traditional exhaust rubber hangers cos they're too floppy and move too much.
Decided to get these solid bolt-on Bobbin-type rubber mounts in halfords, meant for rover mini's.

bobbin.jpg


some ppl use them to support the exhaust under shearing or tension load but that'll stress & shorten the lifespan prematurely.
the best way is to keep them under compression, which means I'll have to fabricate a frame to hang the silencer & rest down on the bobbins.

started with these two brackets using the only stainless bar I have available.

IMG_20200419_160154.jpg


welded the lower bracket under the chassis beam and installed the new frame & bobbins

IMG_20200419_184348.jpg
IMG_20200419_172303.jpg


Using the previous mount to help keep the silencer perfectly positioned/aligned to the bumper while I tack weld this new frame in place.
but afterwards I realised the two different vertical & lateral mounts were actually locking each other in place, DOH! :rolleyes:

IMG_20200419_181743.jpg


impossible to cut the old mount off with my bulky grinder or dremel, so I slowly hacksawed it off ?

IMG_20200419_183917.jpg


welded it all up

IMG_20200419_200719.jpg
IMG_20200419_200742.jpg


I've essentially created a carry handle for the exhaust lol ?

IMG_20200419_200812.jpg


fits much better and now cusioned on rubber mounts with minimal movement ?
I'd like to add a 3rd lateral supporting bobbin to stop it swaying sideways but I can always add that later on

IMG_20200419_201440.jpg
IMG_20200419_201539.jpg
IMG_20200419_201504.jpg


now I can finish reassembling the rear suspension
 
undersealed the rear end

IMG_20200420_144140.jpg


wirebrushed & painted the suspension bits

IMG_20200420_154404.jpg
IMG_20200420_163359.jpg
IMG_20200420_203457.jpg


the OEM bolts feature this 1mm thinner shank so that the whole length of the bolt doesn't seize inside the steel bush insert.
the spare bolts I used on the left didn't have this feature

IMG_20200420_214925.jpg


so I machined them with the 11mm diameter feature

IMG_20200420_215702.jpg
IMG_20200420_220601.jpg
IMG_20200420_222933.jpg


rear suspension is now overhauled, assembled & ready to install ? ?

IMG_20200420_232804.jpg
IMG_20200420_232826.jpg
IMG_20200420_233139.jpg
IMG_20200420_233234.jpg
 
this morning I was sent some spare cg13 pistons I brought from Sir Chris, incase I crack a few ringlands in the future :p

IMG_20200421_143214.jpg


spent a few hours cleaning & machining the length of each bolt so that there's no exposed threads to rust and seize/snap the next time I wanna take em out. (close to naming each one too lol)
was looking forward to bolting up the axle but then realised the whiteline lower arm PU bushes was very sticky and needs regreasing, so off it comes again :rolleyes:

IMG_20200421_173751.jpg


pressed the dried steel bush insert out, machined smooth, regreased and reinstalled the 2nd time

IMG_20200421_173811.jpg


axle is finally bolted on, phew ☺?

IMG_20200421_211410.jpg


accessing the spring adjusters is soo much easier now ?

notice there's 20mm more threads available so it could potentially drop it even lower, but the stiff shorter spring is currently already fully relaxed so one day I'd have to reduce the dampers travel by either remounting it lower on the axle or fit droop limiters

IMG_20200421_211438.jpg
IMG_20200421_211507.jpg
 
finished assembling the brakes, pan hard, spring covers, drop links and rear bumper

IMG_20200422_150245.jpg
IMG_20200422_150303.jpg


yay it's such a relief to drop her back on all 4's after 2 months of hard work stuck on axle stands during the lockdown ?

IMG_20200422_161931.jpg


she was absolutely filthy with rusty grinding dust outside & inside ?

IMG_20200422_195404.jpg


gave her a much needed wash, much better ?

IMG_20200422_203501.jpg
IMG_20200422_203543.jpg
 
wow ? would be a dream to have it that preserved ? good as new.

Wow indeed!

Golf restored to OEM as new (show) standard & picture 17 of 20 is remarkable for fanatical attention to detail that is beyond my comprehension & “bangernomics” cost reasoning when applied to a 31 year old runabout with an apparent 132K on the clock. :confused:
 
time to repaint this rusty strut brace

IMG_20200423_153308.jpg
IMG_20200423_160546.jpg
IMG_20200423_190913.jpg


better ?

IMG_20200423_192817.jpg


setting up the corner balancing scales

IMG_20200423_202909.jpg


discovering a few big issues with my balancing setup:
-these scales are limited to 300kg and with a full tank the front right corner is exceeding it,
-the stiffer spring rates are alot more sensitive to the slightest travel, so 1mm may throw the scales off by few kg,
-all the dampers have this inconsistant friction / binding, due to the seals & pistons, which again throws the sensitive scales wayy-off. (the rear dampers could be disconnected but the front struts can't and they have the highest friction)

all this makes the tool pretty useless :rolleyes:?

anyway, the only readings I managed to get is this. trying to correct the balance with very inconsistant scales was infuriating and gave up.

Screenshot_20200423_221214_com.jpg


corner balancing ain't essential at this point anyway cos tbh it looks like trackdays or shows ain't gonna happen for a longg time during this global crisis / shutdown ??
 
the old alternator has been struggling to fully charge the battery up, only reaching 13.4v so the next morning only has 12v

IMG_20200424_114451.jpg


replaced it with a spare which reaches 13.7v

IMG_20200424_121653.jpg


brought a furry wind sock for the outside mic and placed it within the bumper near the backbox which seems to work in capturing the exhaust noise

IMG_20200411_140635.jpg


went for a test drive on this gorgeous day and wow she feels really good & fun ?

no more rattles in the back. the new tyre & suspension setup feels soo responsive, minimal bodyroll and grips really hard whilst whizzing round tight bends with no sign of under or over steer, probably due to the warmer temps.

mixing the stereo cabin mic with the new exhaust mic sounds great ?



IMG_20200424_140732.jpg
IMG_20200424_140946.jpg


even after greasing, the swaybar polyurethane bush still tends to dry out & bind/stick to the bar which affects the roll-stiffness and made the old bracket on the axle crack from the twisting stress

IMG_20200425_162338.jpg


so I wirebrushed the paint off to loosen it slightly and used dry graphite powder inside the bush rather than goopy grease which tends to be squeezed out under pressure. seems to have worked and there's abit less friction now

IMG_20200425_163803.jpg
IMG_20200425_170729.jpg


catch cans manage to grab 200ml of clear water/fuel vapour from the crankcase after 1500miles since february

IMG_20200425_174045.jpg
IMG_20200425_174432.jpg
IMG_20200425_174723.jpg
 
the tigersealed gauge pods starting to peel off after years of flexing

IMG_20200427_162743.jpg
IMG_20200427_163359.jpg


fitted some normal covers for now while I'm fixing em

IMG_20200427_165505.jpg


ever since I applied red rubber grease to the electric window rubber seals it's barely slides even worse than before cos it dries into a very sticky thin goop :rolleyes:

so I removed & wiped the rubber grooves clean and applied dry graphite powder instead. slides soo much more effortlessly (y)

IMG_20200428_155920.jpg
 
I always thought the throttle cable running over the engine cover looked abit of an eye sore, it rubs against the painted cover and note how the little printed cable mount for bolting the cable onto the rocker cover sits off-set to the throttle body bracket

IMG_20200501_191356.jpg
IMG_20200501_191341.jpg


the normal cable bracket feeds to the front and over the rocker cover

IMG_20200430_212052.jpg


took apart the pulley

IMG_20200430_214707.jpg


drilled the hole round so I can reposition this pulley on the shaft

IMG_20200501_181021.jpg


marking, chopping & welding the bracket onto it's new vertical position

IMG_20200501_180900.jpg
IMG_20200501_185929.jpg
IMG_20200501_190931.jpg


so now the cable sits vertical going from fully closed to WOT

IMG_20200501_194239.jpg
IMG_20200501_194330.jpg


with the cable exiting at the back I can reroute it like this away from the rocker cover

IMG_20200502_001242.jpg
IMG_20200502_001304.jpg
IMG_20200502_001321.jpg


soo much cleaner & neater :cool:

IMG_20200502_001220.jpg


rocker cover really needs respraying next ?
 
Looks nicer Paul but you have gone from one fairly smooth single 'C' bend in the cable to a convoluted 'S', with much tighter bends, something that anyone designing a bowden cable run tries to avoid, more friction and inevitably more likelihood of the cable becoming 'sticky' in the long term.........
 
Looks nicer Paul but you have gone from one fairly smooth single 'C' bend in the cable to a convoluted 'S', with much tighter bends, something that anyone designing a bowden cable run tries to avoid, more friction and inevitably more likelihood of the cable becoming 'sticky' in the long term.........

It could've gone straight over the TB/fuel rail to reduce the bend but I'd prefer to route it clear out the way of everything for better access & appearance.

The S bend ain't that bad. It's bout as tight as some bicycle brake cables and those still work fine with minimal friction.

As for friction, I lubed the cable and there's very very little friction.
I doubt it'll often get as sticky or worn cos it's just light-duty (compared to my very heavily loaded clutch cable) but even if it does stick, it's very simple to just remove & lube the cable annually or just replace it with another bicycle cable.
 
It could've gone straight over the TB/fuel rail to reduce the bend but I'd prefer to route it clear out the way of everything for better access & appearance.

The S bend ain't that bad. It's bout as tight as some bicycle brake cables and those still work fine with minimal friction.

As for friction, I lubed the cable and there's very very little friction.
I doubt it'll often get as sticky or worn cos it's just light-duty (compared to my very heavily loaded clutch cable) but even if it does stick, it's very simple to just remove & lube the cable annually or just replace it with another bicycle cable.
A brake cable on a bike, and it does not get the degree of use that an accelerator cable on a car does, and does not have to be as free as an accelerator cable, which to give smooth operation, possibly thousands of times a day, has to be really free. I'm sorry Paul this time you have got it wrong. The Nissan engineer that determined the original route for the cable got it right.......A classic case of fashion over form, the aesthetically 'prettiest' solution isn't always the correct answer.:(
 
A brake cable on a bike, and it does not get the degree of use that an accelerator cable on a car does, and does not have to be as free as an accelerator cable, which to give smooth operation, possibly thousands of times a day, has to be really free. I'm sorry Paul this time you have got it wrong. The Nissan engineer that determined the original route for the cable got it right.......A classic case of fashion over form, the aesthetically 'prettiest' solution isn't always the correct answer.:(

I disagree. a bicycle brake cable experiences a lot more tension & strain squeezing the pads hard against the rim during heavy braking compared to a throttle cable which is just moving a lightly spring loaded flap.

the original route maybe good for reliability etc but I have different needs so I modify it while maintaining function.

It ain't bent ridiculously tight, it's well lubed and it still slides very easily & smoothly whether it's with the pedal or my own fingers. It works & does what I want at end of the day.

Only way to discover what's really right or wrong is by trial & error, by doing it, by R&D.
your standards & criterias are very different to mine.
 
I disagree. a bicycle brake cable experiences a lot more tension & strain squeezing the pads hard against the rim during heavy braking compared to a throttle cable which is just moving a lightly spring loaded flap.

the original route maybe good for reliability etc but I have different needs so I modify it while maintaining function.

It ain't bent ridiculously tight, it's well lubed and it still slides very easily & smoothly whether it's with the pedal or my own fingers. It works & does what I want at end of the day.

Only way to discover what's really right or wrong is by trial & error, by doing it, by R&D.
your standards & criterias are very different to mine.
As they say the proof of the pudding is in the eating, it's not always necessary to try to re-design the wheel. It's not the matter of 'moving a lightly spring loaded flap' but more the ability of said flap's springing having the ability to close again against the added friction of the cable.......NOT a 'fail safe' situation.
My 'standards and criteria' are based on over 50 years of experience, in industry, designing mechanisms in production line machinery, both in the lamp making and automotive fastener industries, where things have to move fast, consistently and for a very high number of operations.
 
As they say the proof of the pudding is in the eating, it's not always necessary to try to re-design the wheel. It's not the matter of 'moving a lightly spring loaded flap' but more the ability of said flap's springing having the ability to close again against the added friction of the cable.......NOT a 'fail safe' situation.
My 'standards and criteria' are based on over 50 years of experience, in industry, designing mechanisms in production line machinery, both in the lamp making and automotive fastener industries, where things have to move fast, consistently and for a very high number of operations.

Mmm pudding ? I'll see how it goes. this ain't reinventing the wheel, it's reconfiguring it to a different spec. the spring has more than enough tension to return closed 'provided' the cable mechanism is regularly maintained (which is easy to service on mine). if at any point it begins to show signs of binding at all, it's simple to relax/reroute it another way.
 
sprayed the A pillars black ?

IMG_20200502_184741.jpg
IMG_20200502_184959.jpg


with the throttle cable sorted out the way, it's time to sort out the tatty faded engine cover.
rather than remove, strip, prep & respray the current cover, I have a spare cover in the garage I could clean & respray from scratch instead

IMG_20200503_171303.jpg


gave it a good soak, scrub & wirebrush in boiling hot Persil

IMG_20200503_175228.jpg


after a blast with the jet wash soaking me everywhere ? it turned out nice & clean

IMG_20200503_180840.jpg
IMG_20200503_180903.jpg


wirebrushed the oxide off every nook cranny

IMG_20200503_210848.jpg


and resprayed ??

IMG_20200503_212543.jpg
IMG_20200503_224436.jpg
 
Cable running over the rocker has always annoyed me, just never enough to think about moving it...

Can't imagine it being a problem, if the pedal doesn't feel drastically different I'd call it fine!

@John_D
I've yet to see you post something good about the work Paul's done yet, on his own car... One day maybe

Sent from my CLT-L09 using Micra Sports Club mobile app
I have posted many 'likes' for Paul's work on his car, but I do comment, occasionally, on some things negatively, when it becomes obvious that Paul has had no formal experience on metallurgy and mechanical engineering. The vast majority of improvements/developments that Paul has done to his car are a credit to him and his persistence to get things better. The only person that doesn't make the occasional mistake is someone that does nothing.....
 
I have posted many 'likes' for Paul's work on his car, but I do comment, occasionally, on some things negatively, when it becomes obvious that Paul has had no formal experience on metallurgy and mechanical engineering. The vast majority of improvements/developments that Paul has done to his car are a credit to him and his persistence to get things better. The only person that doesn't make the occasional mistake is someone that does nothing.....

aye, constructive criticism.
I only know soo much to achieve certain tasks, doing my best at making continuous incremental improvements to get closer to the ideal goal.
sometimes I may miss something that another one spots and so it helps to share those thoughts/concerns so I can make better decisions & progress forward.
 
sanded the letters down

IMG_20200504_110734.jpg


discovered I can use dettol wipes to clean dirt/dust off the fresh base coat like a tack cloth in preparation for the top coat

IMG_20200504_113328.jpg


laquered and looking nice ?

IMG_20200504_135235.jpg
IMG_20200504_135318.jpg


removed the old cover. cams showing signs of oil cooking/varnishing on the lower stress/non-touching side of the lobes?

IMG_20200504_123614.jpg
IMG_20200504_123627.jpg


fitted the new cam cover and what a huge difference, the red just 'pops' out from the matt black engine bay :love::cool:? gorgeous

IMG_20200504_143609.jpg
IMG_20200504_143659.jpg
 
sanded the letters down

View attachment 69257

discovered I can use dettol wipes to clean dirt/dust off the fresh base coat like a tack cloth in preparation for the top coat

View attachment 69258

laquered and looking nice ?

View attachment 69261View attachment 69262

removed the old cover. cams showing signs of oil cooking/varnishing on the lower stress/non-touching side of the lobes?

View attachment 69259View attachment 69260

fitted the new cam cover and what a huge difference, the red just 'pops' out from the matt black engine bay :love::cool:? gorgeous

View attachment 69263View attachment 69264
So much nicer Paul than the K12 cam cover, covered up with the damned great plastic airbox/plenum, looks great:cool:.
 
sanded the letters down

View attachment 69257

discovered I can use dettol wipes to clean dirt/dust off the fresh base coat like a tack cloth in preparation for the top coat

View attachment 69258

laquered and looking nice

View attachment 69261View attachment 69262

removed the old cover. cams showing signs of oil cooking/varnishing on the lower stress/non-touching side of the lobes?

View attachment 69259View attachment 69260

fitted the new cam cover and what a huge difference, the red just 'pops' out from the matt black engine bay :love::cool: gorgeous

View attachment 69263View attachment 69264
That's a great tip to use the dettol wipes as a tack cloth,I'm often wondering what I should be using.Will give that a try some time might have to use another brand.
Great discovery.

Sent from my ASUS_T00P using Micra Sports Club mobile app
 
ever since I moved this lathe rpm disc (cos I used one of the threaded rings for holding the manual hand crank) the sensor was never used

IMG_20200506_095809.jpg


so I printed this quick mount

IMG_20200506_095535.jpg


to position the sensor correctly and now I have an rpm readout

IMG_20200506_101123.jpg


time to wet & dry sand the grill in the sun. interesting to see it was originally from a blue micra but resprayed green twice

IMG_20200506_122830.jpg
IMG_20200506_124131.jpg


primered & painted with only limited amounts I have remaining. still a huge gaping crack I cba to bodyfill but at least it's the right colour now

IMG_20200506_125718.jpg
IMG_20200506_191110.jpg


friend mentioned to me bout a brake bleeder that uses tyre pressure pressurise the reservoir & continuously push fluid through (rather than operating the pedal) while you bleed each corner.

I modelled this cap to seal against the reservoir opening and connect to the tyres with a hose

cap.jpg

IMG_20200506_225904.jpg


ooh it's nice when things fit perfectly :cool:

IMG_20200506_230150.jpg
 
ever since I moved this lathe rpm disc (cos I used one of the threaded rings for holding the manual hand crank) the sensor was never used

View attachment 69344

so I printed this quick mount

View attachment 69343

to position the sensor correctly and now I have an rpm readout

View attachment 69345

time to wet & dry sand the grill in the sun. interesting to see it was originally from a blue micra but resprayed green twice

View attachment 69346View attachment 69347

primered & painted with only limited amounts I have remaining. still a huge gaping crack I cba to bodyfill but at least it's the right colour now

View attachment 69348View attachment 69349

friend mentioned to me bout a brake bleeder that uses tyre pressure pressurise the reservoir & continuously push fluid through (rather than operating the pedal) while you bleed each corner.

I modelled this cap to seal against the reservoir opening and connect to the tyres with a hose

View attachment 69352
View attachment 69350

ooh it's nice when things fit perfectly :cool:

View attachment 69351
The secret with these Paul is to use a spare tyre with very low pressure in it, say 10/15psi or so. Much higher and you will empty the reservoir rather quickly..... ;)
 
fitted the resprayed front grill along with the badge and she looks back to normal again :D

IMG_20200507_132447.jpg
IMG_20200507_132530.jpg
IMG_20200507_144549.jpg
IMG_20200507_144250.jpg


went for a drive to buy some stuff.



Wow I'm forgetting how she sounds & feels after only getting to drive kassandra very infrequently every 2 weeks :oops:

Her exhaust seems a lot quieter, there's no more rattles, the ride is plush but firms up when compressed, and these tyres have a lot of grip on the warm floor. Back of my mind is thinking this is pretty fast, will my suspension hold? It'll take time to relearn & regain trust in her new setup before I can push hard.

Broke the first bleeder cap as I pressed a 6mm tube into the slightly smaller hole, so I reprinted it with an integrated 7mm nozzle for the hose

IMG_20200507_203211.jpg


got this shraeder bend adapter in halfords to join the hose to the tyre valve

IMG_20200507_171518.jpg

IMG_20200507_204713.jpg


hooked up the front 40psi tyre to the reservoir as a 1st test

IMG_20200507_204700.jpg


can see the pressure pushing up the cap tightly and the struggling single o-ring is hissing slightly, so it ain't 100% airtight yet, but it's certainly effective cos it applies the brakes as though I'm lightly touching the pedal ?

I'll refine the cap with a better seal and use a spare tyre inflated to a softer 15psi instead ?
 
fitted the resprayed front grill along with the badge and she looks back to normal again :D

View attachment 69362View attachment 69363View attachment 69365View attachment 69364

went for a drive to buy some stuff.



Wow I'm forgetting how she sounds & feels after only getting to drive kassandra very infrequently every 2 weeks :oops:

Her exhaust seems a lot quieter, there's no more rattles, the ride is plush but firms up when compressed, and these tyres have a lot of grip on the warm floor. Back of my mind is thinking this is pretty fast, will my suspension hold? It'll take time to relearn & regain trust in her new setup before I can push hard.

Broke the first bleeder cap as I pressed a 6mm tube into the slightly smaller hole, so I reprinted it with an integrated 7mm nozzle for the hose

View attachment 69367

got this shraeder bend adapter in halfords to join the hose to the tyre valve

View attachment 69366
View attachment 69369

hooked up the front 40psi tyre to the reservoir as a 1st test

View attachment 69368

can see the pressure pushing up the cap tightly and the struggling single o-ring is hissing slightly, so it ain't 100% airtight yet, but it's certainly effective cos it applies the brakes as though I'm lightly touching the pedal ?

I'll refine the cap with a better seal and use a spare tyre inflated to a softer 15psi instead ?

The seal will probably hold 15 psi Paul, you were pushing your luck with 40 psi, not sure the reservoir to main cylinder seal would be very happy with that either, probably a good thing that your cap seal was not holding up....... ;)
 
The seal will probably hold 15 psi Paul, you were pushing your luck with 40 psi, not sure the reservoir to main cylinder seal would be very happy with that either, probably a good thing that your cap seal was not holding up....... ;)

hehe indeed
 
Hey pollyp, I've been following this thread for ages, ever since 2012'ish. The attention to detail and engineering that goes into this car is pure next level. If everyone even gave half of what you are doing, we would have a much more sustainable future. Truly inspiring!

I've owned a few K11s, B13s, and now moved on to the Nissan Leaf. It's a totally different world, have you ever thought about an electrical future for Kassandra?

Here's my buildthread on the ZE0 if you want to take a peek :) : http://www.japtoys.net/forum/viewtopic.php?f=10&t=3613
 
Hey pollyp, I've been following this thread for ages, ever since 2012'ish. The attention to detail and engineering that goes into this car is pure next level. If everyone even gave half of what you are doing, we would have a much more sustainable future. Truly inspiring!

I've owned a few K11s, B13s, and now moved on to the Nissan Leaf. It's a totally different world, have you ever thought about an electrical future for Kassandra?

Here's my buildthread on the ZE0 if you want to take a peek :) : http://www.japtoys.net/forum/viewtopic.php?f=10&t=3613
Very interesting read:cool:
 
Hey pollyp, I've been following this thread for ages, ever since 2012'ish. The attention to detail and engineering that goes into this car is pure next level. If everyone even gave half of what you are doing, we would have a much more sustainable future. Truly inspiring!

I've owned a few K11s, B13s, and now moved on to the Nissan Leaf. It's a totally different world, have you ever thought about an electrical future for Kassandra?

Here's my buildthread on the ZE0 if you want to take a peek :) : http://www.japtoys.net/forum/viewtopic.php?f=10&t=3613

Hi, thanks for the compliments Dala ?
she's been a labour of love and sharing my journey here may hopefully help out ppl who comes across the same challenges and inspire them to pursue their curiosity, making things better.

not thought about going electric yet after having invested all of myself into kassandra. I simply don't have any space in the house or especially finance to consider another project.

that's a fascinating build of yours. love the detail & passion u put into it (y)
 
time to freshen up & paint the calipers

IMG_20200512_172344.jpg
IMG_20200512_185846.jpg


begin stripping it down

IMG_20200512_213728.jpg


pistons are still nice & shiny smooth

IMG_20200512_213745.jpg


rear pistons all good, the self-adjusting thread in the middle can still rotate freely, and the handbrake mechanism works fine

IMG_20200512_213755.jpg


overall they're mechanically fine. just needs a good wirebrush & paint
 
ordered some LK0 base coat & laquer from NuAgane to see if it's a better match to the factory paint

IMG_20200515_150638.jpg


I didn't have any right size spare copper washers for the banjo bolts so to freshen up the old washers, I sanded em flat with wet dry on glass.

not to self: don't try sanding thin washers with just fingers cos silly me eventually sanded through my fingerprint till it was bleeding! ?? ouch
it's only afterwards I found that I could sand the washers by using an M10 nut with the threaded shaft in the middle keeping the washer located. learning from painful mistakes ey? ?

IMG_20200515_165153.jpg


fresh brakes fitted :cool:

IMG_20200515_170823.jpg
IMG_20200515_171900.jpg


bleeding the whole system with the new tool, works gr8 with 20psi (y)

IMG_20200515_180630.jpg


beautiful ?

IMG_20200515_184607.jpg
IMG_20200515_184622.jpg
IMG_20200515_184905.jpg


I recently had to replace the alternator cos the old one's been struggling to reach 13.3v and charging the battery.
tonight I was checking all 3 of em, they all had the same coil resistances, same good condition sliding contacts but I noticed that the removable rectifier/contact slider is simply connected to the circuit by this spring fork

IMG_20200515_215356.jpg


could it be that this fork and the rectifier end simply oxidises & gets dirty over time which degrades the connection and reduce the voltage output? that's another silly design exposed to the elements.

IMG_20200515_215418.jpg
IMG_20200515_215430.jpg


I'll clean em all up & see if it improves the output reading
 
cleaning the alternator contacts made no difference.

multimeter still reads:
alternator = 14v
original battery +ve terminal = 13.8v
extended battery cable under passenger seat = 13.5v
nissan datascan = 13.3v

seems like there's a lot of resistance between the alternator, loom and battery.
unbolted the battery extension from the original +ve end and wirebrushed it all to bare metal.
looks like they all had some oxide buildup.

IMG_20200517_164749.jpg
IMG_20200517_170202.jpg


see if that makes a difference
 
stripped down the 3d printer to fix a few issues.
- the top mounted spool holder pulls the filament over a long distance down to the extruder motor.
this puts too much strain on the plastic filament because it naturally wants to spring back into a coil due to the way they're made & stored.
a few hours after finishing each print, heat from the hot end would soak afew cm up the filament making it more brittle until the bending forces snap the filament making it tangle within the spool.
- the original frame sat too low so I had to roughly lift it up so the bearings for the printer bed clears the desk.

IMG_20200518_190103.jpg


I was gonna just attach some feets to the frame to lift it higher but then thought lets fit some adjustable feets with nuts & bolts too, so I can level it to the uneven desktop & stop it wobbling.

IMG_20200518_210737.jpg
IMG_20200518_210808.jpg


also welded the spool mount to the front so that the filament doesn't have to straighten out as much & over a shorter distance to the extruder

IMG_20200518_213631.jpg


installed all the sliders & wiring

IMG_20200518_235335.jpg
IMG_20200518_235404.jpg


all assembled & working again. hopefully overnight the filament won't snap again while I'm sleeping

IMG_20200519_001908.jpg
 
Couple of questions

Whys the side panel off your pc
What is that cpu cooler, I know its not but it makes me think of the Thermaltake turbine ones.

Also cool k11 build (I guess I need to mention that in a thread about the car lul)
 
Couple of questions

Whys the side panel off your pc
What is that cpu cooler, I know its not but it makes me think of the Thermaltake turbine ones.

Also cool k11 build (I guess I need to mention that in a thread about the car lul)

Runs a lot cooler & quieter with no covers and all fans dialled to near silent.

Its a zalman CNPS9900 cooler.

ImgW.jpeg
 
Back
Top