• Please only use these forums for blogs, they are not a discussion forum

PollyMobiles Rebuild

OP
OP
pollyp

pollyp

Club Member
the staining appears when i leave it in tub for awhile and then take em out.
aways rinsed it out under tap, spray wd40, wipe dry then oiled with 10w40
 

r-reg-sr

-------
Site Supporter
oooooh that washing machine powders got a little power still-how much will it affect?
like when you had the cuts in the hand-it gives that nice feeling using it:laugh:
 
OP
OP
pollyp

pollyp

Club Member
oooooh that washing machine powders got a little power still-how much will it affect?
like when you had the cuts in the hand-it gives that nice feeling using it:laugh:

i'm wearing vinyl groves here, brought pack of 100 for fiver, so no dirty hands or cut fingers. though when i tried wash powder at sulurs with couple of scuffed knuckles n fingers it stings like heck:doh:
 
OP
OP
pollyp

pollyp

Club Member
took apart the oil pump

2010 09 (277).JPG


cleaned

2010 09 (279).JPG


assembled

2010 09 (280).JPG


fit rear crank seal

2010 09 (283).JPG


dunk sump in tub of persil

2010 09 (284).JPG


nice n clean

2010 09 (286).JPG
2010 09 (287).JPG


work on the head next
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
hey does anyone know if PTFE sheet of 5mm thick will be ok to withstand the temps between the engine block & inlet manifold?

i was thinking of buying a sheet of 5mm ptfe and make an insulating spacer gasket for the inlet manifold to reduce inlet temps.

wiki says ptfe melts at 327C but dunno if the block will reach that and melt it under heat soak

or maybe use rubber sheet?
 
OP
OP
pollyp

pollyp

Club Member
valves taken out

2010 09 (288).JPG


head is washed

2010 09 (290).JPG
2010 09 (291).JPG
2010 09 (292).JPG
2010 09 (294).JPG


dremeled grooves on an old plug to tap n clean the sparkplug holes

2010 09 (293).JPG


washed valves

2010 09 (297).JPG


to clean the baked residue on the valve head i spun the valves on a pillar drill and lathe with a blade & scorch pad

2010 09 (298).JPG
2010 09 (299).JPG
2010 09 (301).JPG


valves fitted

2010 09 (303).JPG
2010 09 (302).JPG
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
head bolted up. will need to install new HG when the engines needed.

2010 09 (304).JPG


cams on

2010 09 (306).JPG
2010 09 (307).JPG


oil pickup on

2010 09 (309).JPG


fitted the turbo drain plug

2010 09 (310).JPG
2010 09 (311).JPG


blank off the un-used port at back with nut & bolt

2010 09 (312).JPG
2010 09 (314).JPG


wirebrushed the dizzy mount top bracket

2010 09 (315).JPG
2010 09 (316).JPG


engines pretty much complete, moved out the way and move on to the gearbox

2010 09 (317).JPG


remove endplate & washers

2010 09 (319).JPG


reverse gear switch

2010 09 (318).JPG


alot of metal bits on the plug suggests there's been quite abit of gear crunching

2010 09 (321).JPG


casing unbolted

2010 09 (323).JPG


bash from around the edges of the casing to free it from the locating dowels & sealant then lift the case up. something inside prevented the case from being lifted straight up but finally managed by lifting and tilting the case

2010 09 (326).JPG


this is what was catching. the upper shaft support on the casing for the reverse gear cog catches on the Topgear selector fork therefore ya tilt the casing to clear the fork

2010 09 (327).JPG
2010 09 (328).JPG


pull out the long shaft that all the selector forks pivot on then remove the topgear fork

2010 09 (329).JPG


3-4th fork and 1-2nd fork

2010 09 (330).JPG


heres the selector shaft. notice the ball & spring at the end of the shaft on the left, this is what holds the selector in gear

2010 09 (331).JPG


pull out the reverse gear shaft & cog to access the retaining bracket

2010 09 (332).JPG


unbolt the retaining bracket

2010 09 (333).JPG


then lift out both gears

2010 09 (334).JPG


followed by the differential

2010 09 (337).JPG


empty gearbox. need to figure how to remove the selector arm and clutch arm from the case. seems to be held on by spring pins

2010 09 (339).JPG


heres the neutral switch which seems to have been snapped off

2010 09 (340).JPG
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
the previous block of wood above the silencer fell out so the exhaust was banging about. so sawed afew more wood and ziptied em to the box. the rubber hangers were also abit tired so afew more zipties. the box is now rigidly fixed to the chassis, no more banging around.

2010 09 (341).JPG


the clutch fork and gear selector seems to be secured by 2 roll pins inside one another so i grab some nails of similar size, cut & file the tip flat then gradually hammer the pin through

2010 09 (343).JPG


selector rod seperated

2010 09 (344).JPG


clutch fork off

2010 09 (345).JPG
2010 09 (346).JPG


heres the dirty empty case

2010 09 (347).JPG
2010 09 (348).JPG


the 5th/reverse return spring housing needed a good twist & bash to loosen off

2010 09 (349).JPG


clean n inspect the gears

2010 09 (350).JPG


primary input shaft

2010 09 (351).JPG
2010 09 (352).JPG


secondary shaft

2010 09 (363).JPG
2010 09 (355).JPG


1st gear

2010 09 (357).JPG


2nd gear

2010 09 (358).JPG


3rd gear

2010 09 (359).JPG


4th gear

2010 09 (362).JPG


top gear

2010 09 (353).JPG
2010 09 (354).JPG


case all washed n wiped down :) Mmmm

2010 09 (365).JPG
2010 09 (366).JPG
2010 09 (367).JPG

2010 09 (368).JPG
2010 09 (369).JPG


clean & install the 5th/reverse return spring

2010 09 (373).JPG
2010 09 (376).JPG
2010 09 (377).JPG

2010 09 (378).JPG
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
wirebrushed selector arm

2010 09 (380).JPG


clutch arm

2010 09 (382).JPG


and clutch fork

2010 09 (384).JPG


fit selector arm to shaft

2010 09 (385).JPG


selector reinstalled

2010 09 (387).JPG


fit diff & gears

2010 09 (389).JPG


heres the selector mechanism

2010 09 (397).JPG
2010 09 (396).JPG
2010 09 (398).JPG


selector fork

2010 09 (399).JPG


fitted selector mechanism & 1st fork

2010 09 (401).JPG


reverse cog

2010 09 (402).JPG


2nd & 3rd selector forks

2010 09 (403).JPG
2010 09 (404).JPG


cleaned the other casing

2010 09 (406).JPG


apply sealant

2010 09 (409).JPG


bolted up

2010 09 (411).JPG


clutch fork installed

2010 09 (414).JPG


sealed & stored

2010 09 (415).JPG
 
Last edited:

r-reg-sr

-------
Site Supporter
did you see any damage on any gears/mesh thingy
and in dificulty how high would you place this strip down rebuild?
thanks
 
OP
OP
pollyp

pollyp

Club Member
the gearbox is like new, not much wear.

stripping the box was easier than i thought. as long as ur methodical, organised, take reference pics, pay attention to details & cleanliness its like taking a bike apart.
 
OP
OP
pollyp

pollyp

Club Member
took apart the thermostat housing, tis abit gunged up but seems fine once wiped. won't be needing the housing as one of the hose outlets is chipped but the stock thermostat is a keeper

2010 09 (426).JPG
2010 09 (427).JPG


wirebrushed the alternator belt tensioner

2010 09 (428).JPG
2010 09 (429).JPG


brushed the coolant return pipe

2010 09 (431).JPG


couple bits wont be needing and put in buy&sell

2010 09 (434).JPG
2010 09 (438).JPG
2010 09 (440).JPG
2010 09 (441).JPG


alternator with plug type connector rather than hook end connectors on mine. but dunno if one of the plug terminal pins broken off or if its suppose to be like that? (ie. the bolt-on connector bit is -ve ground while the one-pin terminal plug is +ve) or is it broke and bin it?

2010 09 (443).JPG
2010 09 (442).JPG


wirebrushed the exhaust

2010 09 (450).JPG
2010 09 (447).JPG

2010 09 (451).JPG
2010 09 (453).JPG


disassembled the janspeed manifold. prob sell it once turbo is on

2010 09 (456).JPG
2010 09 (455).JPG


taking the dizzy apart. cap islittle cracked n seized screws snapped off

2010 09 (457).JPG


rotor off

2010 09 (458).JPG
2010 09 (459).JPG


remove hall sensor disc

2010 09 (460).JPG
2010 09 (461).JPG
2010 09 (462).JPG
2010 09 (463).JPG


hall sensor unit

2010 09 (464).JPG


tried taking it apart inside but seems the circuit & connectors were internally wired together and so pry it apart wrecked it, meh

2010 09 (468).JPG
2010 09 (472).JPG


inductor coils

2010 09 (467).JPG


remove bearing from shaft

2010 09 (473).JPG
2010 09 (474).JPG


i think thats almost everything cleaned. now to research into gauges, bov/recirc valves, boost control
 
Last edited:

Shaun

***StaGGeRed***
Looking awesome! the offer is still there if you wanna come do mine... :grinning:
Would new exhaust rubbers make the problem go away?
 
OP
OP
pollyp

pollyp

Club Member
Looking awesome! the offer is still there if you wanna come do mine... :grinning:
Would new exhaust rubbers make the problem go away?

to clean urs? i've almost had enough of scrubbing & rebuilding the engine & gearbox, lotsa labour

yeah the rubbers are abit tired n soft n need replacing with stuffer hangers
 
OP
OP
pollyp

pollyp

Club Member
messaged the seller bout the quoted 12kg/6kg f/r springs and replied that it was a typo and i'll be sent 5kg/4kg f/r springs
 
OP
OP
pollyp

pollyp

Club Member
just comparing rear engine mounts, heres the rear mount from the 1.3 turbo'd engine, which is the same as the blue micras original mount

2010 09 (481).JPG


and heres one i grabbed from scrappy during the grey/blue micra rebuild which didn't fit, twas the same as the grey micras original mount that pushed the engine too far forward

2010 09 (482).JPG


there's a clear 10-20mm height difference. both of the rubber inserts are the same number and design, its just the metal mount thats changed.
thinking bout it, the scrapyard rubber mount and the mount bracket that didn't fit correctly (ie still pushed the engine too far forward) was prob from a 1L and i didn't know back then cos i was just checking the rubber insert numbers and thought oh, same number as the correct fitting blue micras mount so they must be the same. apparantly not

2010 09 (483).JPG


i feel my current engine mounts shifting abit when on/off power at low revs, not good for solid janspeed manifold, so wash cleaned the spare turbo engines rear mount

DSC03241.JPG


taped one end

DSC03242.JPG


and carefully filled with PU sealant

DSC03244.JPG


says it cures from humidity. plonked it on top of combi boiler for next few days
 
Last edited:

baguete

Site Supporter
1.0 rear engine mount turns the engine to the front, me and a friend tryed it some weeks ago, as his 1.3 mount was knackered and we tryed a 1.0 mount, and it didnt fit right...
 
OP
OP
pollyp

pollyp

Club Member
was changing my parents pug 307 discs n pads as they're running thin. what a ball ache of a car to work on :doh: they don't use any usual size bolts or torx heads so had to go buy so new ones and the rear caliper piston doesn't twist n retract easily with some nose pliers like on mine, it just keeps spinninggrr gonna have to go buy a £50 caliper piston rewind tool tomorrow just for this car, if theres any shop that has any and is open. damn french cars
 

r-reg-sr

-------
Site Supporter
love the sealant move!! filled in all them original holes in the rubbers making it stiffer
what are they playing at these french ones?sounds nightmare'sh
 
OP
OP
pollyp

pollyp

Club Member
had to 20miles to halfords in durham this morning to get this £32 caliper rewind tool. twas ####ing down like mad all day which doesn't make it comfy getting wet in garage.

tis a handy tool but didn't work first time cos the plate that braces against the inner side of the caliper was too wide n flat n touching the edges of the caliper therefore the tools axis is offset to the caliper piston and jamming every so often.

so i angle grinded the thing to remove some of the corner edge till it all fits into the caliper cavity and with both axis aligned it works abit better.

both rear disc n pads replaced. taking the front left disc off, why did they use such small torx screw to hold the disc to the hub, which is bound to seize and round off the head, even after some blow torching n soaking in oil. so had to drill the screw out. sorted the front brakes and by chance in my box of screws n bolts i found a pair of countersunk metric flat head screws that match the damaged torx screws:grinning: pays off to keep all ur nuts bolts screws etc in boxes

so brakes replaced, took it out country to bed in during the rain. stock brakes warm up quick but then during bedding they easily overheat n go squishy. cooled down on motorway and feels normal now but may bleed the fluid again to be sure.

mom gave me another £30 on top of covering parts/tools cost for labour, neat :p
 
OP
OP
pollyp

pollyp

Club Member
the PU filled engine mount was half curing, so i carefully pelled the tape off to let air humidity cure the other side

DSC03251.JPG
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
the sealant still seems to be squishy inside after fews day on top of radiator.
even drilled couple holes to let air in but drill bit just gets covered in wet sealant every time

DSC03257.JPG


i'll just fit it n try one day

better use 2-pack mix next time
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
ok after several days on the radiator and couple drillled holes, the sealant seems to have cured now. will fit it soon
 
OP
OP
pollyp

pollyp

Club Member
BC coilovers still hasn't arrived ffs. rang the guy and he says he's waiting on the next shipment to arrive from BC which has been delayed but estimates he'll get it by mon and deliver to me by tues :mad: thats what he said last time i enquired bout it before ordering.
it'll be over a week since i ordered and his ebay list says est 2-3 days plus his stated springrates is wrong. do i point this out to ebay or just leave it?
 
it'll be over a week since i ordered and his ebay list says est 2-3 days plus his stated springrates is wrong. do i point this out to ebay or just leave it?
Did you point this out to him and he still didn't fix it? If so, yeah, and if not, I'd point it out to him in a "by the way" message now and if it's not fixed by Tuesday and the gear hasn't arrived follow it (or both issues) up with eBay.
He could be a dodgy manipulator or just lazy/forgetful :laugh:
 
BC coilovers still hasn't arrived ffs. rang the guy and he says he's waiting on the next shipment to arrive from BC which has been delayed but estimates he'll get it by mon and deliver to me by tuesgrr thats what he said last time i enquired bout it before ordering.
it'll be over a week since i ordered and his ebay list says est 2-3 days plus his stated springrates is wrong. do i point this out to ebay or just leave it?

mate, dont leave it. this is something i hate. why do they sell some stuff without having it? specially on ebay. report that ####### and get them from somewhere else.(Y)

edit: http://www.h-dev.co.uk/index.php?cPath=78_169_297_1036&osCsid=98e8fc6fc6b9dd92b8d68f0811c9914f
 
OP
OP
pollyp

pollyp

Club Member
it seems as though he sends order to BC on a weekly batch basis. why the heck would he state 2-3days if he only orders his stock per week? will call em on mon afternoon to check he definately received stock and dispatched my order. if not, its a notice to ebay for mis-description & poor service.
 
OP
OP
pollyp

pollyp

Club Member
took out the old rear mount n beam

DSC03259.JPG


no wonder the gearstick moves abit at low speed, the rear mount is almost wasted

DSC03260.JPG
DSC03261.JPG


change to the janspeed manifold while i'm there

DSC03268.JPG


good to feel the top end power again. the gear stick movement at low speed on/off throttle has def reduced now

went to scrapyard to get a recirc valve found from saab 900 and micra aircon alternator bracket

DSC03269.JPG
DSC03270.JPG
DSC03271.JPG
 
Last edited:

r-reg-sr

-------
Site Supporter
that and a funny clutch done me over recently
low revs-car jerking-----i was thinking throttle body but you have cracked it their
 
Top