• Please only use these forums for blogs, they are not a discussion forum

K11 Micra (First Car)

Goodies:

J1vZqbA.jpg
 
Going to get some Hammerite on those bars, especially on that panhard rod as it's going to get some abuse. The inner metal sleeve is missing from the bush on the panhard rod. Is that easy to replace or do I need an entirely new bush?
 
Those springs look beautifully packed...as if it was done by a true craftsman, an artist...

Sent from the Magpie's magical nest using Tapatalk
 
Painting of the new boot handle and fuel door has begun!

Primer:
9Bnmiof.jpg


First coat of red:
dkEsGXk.jpg


Just need to allow some time for the paint to harden, then I can sand back the imperfections. I had to do this outside with no way of safely hanging the parts whilst spraying. Next time I'm probably going to use my clothes rack.
 
Final coat of lacquer on (I think), before polish and wax:

9UaKw50.jpg


tG2KWT3.jpg


Also started to strip off the silver paint from the strut brace and panhard rod. Couldn't get one of the bushes off. Any idea how to safely remove them?

O9kjL8n.jpg
 
I used it in the past. It's not as good as it used to be (they took out one of the active chemicals due to some stupid regulation and replaced it with something less powerful). I find it works best if you wrap the parts up in plastic to prevent evaporation.
 
I used it in the past. It's not as good as it used to be (they took out one of the active chemicals due to some stupid regulation and replaced it with something less powerful). I find it works best if you wrap the parts up in plastic to prevent evaporation.

That's what's I'd heard, new legislation or something. I used oven cleaner the other day, not as good but it worked if left for long enough :)
Reckon I'll use nitromors next time
 
More progress! (a little bit)

Gave the boot handle a final pass with some 2000 grit, before a pass with some T-Cut and three passes with Auto Glym resin polish, followed by two coats of Turtle Wax:

SC6v1yc.jpg


Masking tape off and it's done (I masked the seals this time, as trying to get the back on the other boot handle was a nightmare)

QCh2w1P.jpg


So the back has gone from this:

gHY8j33.jpg


...to this:

DW318Zn.jpg


...and then to this:

QA13Ruh.jpg


Really happy with how it looks. Just need to sort out the wrap-around, repaint the rear bumper and boot lid and the rear is done!
 
Today I made the perilous journey to Hampshire to pick up some fancy wheels. Total journey there and back was about 190 miles, used half a tank of petrol - so about £20 :)

Stacked up safely in the back seat:
nlvyqn3.jpg


Popped to my local tyre centre and had the tyres taken off. I'd prefer to work on these without having to worry about the tyres getting in the way. Paid a fiver and it was done in less than two minutes:
fZbJS0P.jpg


The wheels are filthy so they look pretty bad. The previous owner lived on a farm so I guess it'll be down to muddy tracks etc. Giving them a clean tomorrow so I can assess the overall work needed to bring them back up to scratch:
e7FUd6Q.jpg


Tyres ready to go back on once the wheels are finished (they need a good clean too)
u9kZ05V.jpg


Went to visit @Jamie Sykes to drop off his fogs. He gave my tyres the retro white wall treatment:
pERlkxV.jpg

(it's actually just tyre foam)

Got some extra door handles from Jamie so I can get those colour coded. Already rubbed them down with some 240 grit, followed by 600 grit then some primer.
 
Today I made the perilous journey to Hampshire to pick up some fancy wheels. Total journey there and back was about 190 miles, used half a tank of petrol - so about £20 :)

Stacked up safely in the back seat:
nlvyqn3.jpg


Popped to my local tyre centre and had the tyres taken off. I'd prefer to work on these without having to worry about the tyres getting in the way. Paid a fiver and it was done in less than two minutes:
fZbJS0P.jpg


The wheels are filthy so they look pretty bad. The previous owner lived on a farm so I guess it'll be down to muddy tracks etc. Giving them a clean tomorrow so I can assess the overall work needed to bring them back up to scratch:
e7FUd6Q.jpg


Tyres ready to go back on once the wheels are finished (they need a good clean too)
u9kZ05V.jpg


Went to visit @Jamie Sykes to drop off his fogs. He gave my tyres the retro white wall treatment:
pERlkxV.jpg

(it's actually just tyre foam)

Got some extra door handles from Jamie so I can get those colour coded. Already rubbed them down with some 240 grit, followed by 600 grit then some primer.
cheers for getting the bits for me today the fogs look the piece on my car just need the surrounds now and i am loving the boot handle :) how do the tyres look now
 
Tyres look good. I'll need some of that for my other tyres when they go on.

Has the seller replied about the surrounds yet?
 
Small update. Fitted my cigarette lighter!

WPGoU46.jpg


Luckily the wire was already there behind the lower dash trim, so it was just a case of plugging it in.

Also finished up on the door handles. They looked awesome when I took this photo:

d6nwjnh.jpg


...but I put them into a bubble wrap bag to keep them safe and they came out like this:

iKUmCDk.jpg


Looks like I didn't leave the clear coat enough time to cure. I've fitted one anyway, as I can give them another polish whilst they're on the car and have had enough time to harden. I've only done the drivers door. I took the existing black plastic door handle off and the short rod that connects it to the door latch fell out into the door cavity. Luckily we managed to retrieve that, but getting the rod to sit back into the latch whilst keeping the other end connected to the handle, without being able to see the latch itself was a massive pain. We finally got it fitted, but we had no motivation to fit the passenger side at all.

Looks good though...

VIxSDa0.jpg
 
Just bought some 35-40mm lowering springs (front and back). I'm hoping with the 14" wheels the arch gap will close up a bit.

I heard you need Corsa B shocks for the rears though, is that absolutely necessary or just preferred?
 
Just bought some 35-40mm lowering springs (front and back). I'm hoping with the 14" wheels the arch gap will close up a bit.

I heard you need Corsa B shocks for the rears though, is that absolutely necessary or just preferred?

Only need corsa shocks if using massively cut springs.

35mm springs designed for the micra just use original shocks, but I'd always recommend sticking nice new sport shocks in at the same time. Completely un-necessary, just will double the effect on handling :)
 
So 35-40mm springs on stock shocks will be fine then. I thought the rears needed replacing with Corsa shocks because the stock shocks had less travel due to preload from lowering, and risked bottoming out.
 
Possibly, but one step at a time. My insurance provider allows up to 50mm and then has a higher tier past 50mm. Anything past 50mm will cost a fortune and make the car harsh to drive.
 
Tried wiring in my March tail clusters today. I spent ages labeling the wires on the original loom, making an adaptor loom, only to find that when when I hit the brakes both the rear/brake light and the indicator comes on at the same time. Indicator by itself works and flashes as it should. I can't figure it out at all :(
 
@Clodo How much F-ing around did you have to do before you got yours working? Did you have the same issue?

I'm sure the red light has two +ive wires for the rear lamp and the brakes. The brake wire isn't even going to the indicator bulb, so I can can only assume it's something to do with the ground wire, but I'm sure that's correct as I eliminated that as a signal wire of any kind. :confused:
 
Heyyy sorry for the late reply was working yesterday :) took about 20 minutes, just remove the pins out the connection block and keep chopping and changing till everything works :) x
 
I can take a picture tomorrow if that helps but I dunno if your wiring will be the same colour as mine :) but I'll take one anyway :) x
 
Thanks Clodo (^_^ )

I'm going to try and have another stab tonight. I bought some block connectors so it's easier to swap the wires around. Last night I was twist-taping whilst testing, which was cumbersome and it kept breaking. I'll also try and get my better half or brother to help out, as I was having to press the brake pedal with a mop so I could see whether the light was turning on or not!
 
Thanks Clodo (^_^ )

I'm going to try and have another stab tonight. I bought some block connectors so it's easier to swap the wires around. Last night I was twist-taping whilst testing, which was cumbersome and it kept breaking. I'll also try and get my better half or brother to help out, as I was having to press the brake pedal with a mop so I could see whether the light was turning on or not!
i could always give you a hand mate if you needed any help doing it
 
Cheers mate. I won't be finishing work until 7:30 tonight, so I'll try one last time and see how it goes. If you're free Saturday morning, we could try then (assuming it doesn't work).
 
So I *was* going to try and sort the lights out tonight, but as soon as I got home it started chucking it down. It's been sunny all day whilst I was stuck in the office too. Typical.
 
OK THE MARCH LIGHTS ARE FITTED AND WORKING!

Thanks to @Jamie Sykes and his mate, we were able to figure out that the ground wires were incorrectly matched to the cluster, causing a whole manner of problems. We were trying to sort it out whilst parked in a busy street in Cheltenham with a traffic warden making his way down the row of cars so we had to act fast. In the end I went home back to Gloucester and kept looking, armed with the knowledge of which wire was ground (the black one - duh...). I used a multimeter I borrowed off Jamie to work out which wire did what, then worked from there.

Here's the foglight I'll be using. It's supposed to be for a Mazda Bongo :p It'll be mounted into the bumper at some point:

MVlN82C.jpg


Working on the wiring in the back of the car:

9lSsfxg.jpg


I used connector blocks to attach the looms together, as it was easy to swap wires around if they weren't quite right.

5GuEtqM.jpg


These are the notes I took down whilst putting to all together:

coDLbpv.jpg


The resulting harness adaptor before soldering. The red wire connects the reverse light on the passenger side to the lamp on the driver's side:

TgY5By7.jpg


All soldered up and sleeved. I used block connectors for the wires to the foglight and driver's reverse light to act as a disconnect in case I need to take one part out for some reason. I'll replace those with a better solution when I find one:

EnUru8C.jpg


And here they are fitted to the car:

Ut23b0Y.jpg


The passenger side one isn't properly flush, probably due to the sealant residue. I'll figure out something to use as an alternative and refit when possible.

Both reverse lights working:

uEkYmek.jpg


At night:

4UPUjwd.jpg


Was a tough job but we got there in the end!
 
Oh nearly forgot. Here's a text version of my notes, in case of broken image links etc (I hate those!)

Below is a diagram of the back of the male cluster connector (the side the wires go in)
______________
|[1]|______|[4]|
|[2][3]||[5][6]|
----------------

If you're making a harness adaptor like me (which I recommend as it makes reverting to stock easier), then you should have a male and female connector. You can get the male connectors from any K11 Micra, but the female connectors are only removable from pre-facelift K11s, as the facelift and above have the connector moulded onto the cluster housing. The wires may be different depending on the age (and phase) of your Micra, and the cluster type you're using, but this covers facelift March (see also: Cabriolet) lights onto a '99 first Facelift UK K11.

The diagram above shows pins numbered 1-6. These aren't numbered like this by Nissan, I just numbered them like this myself for reference. If you're looking at the back of a male connector, hopefully you'll see the resemblance. If not, then you probably have the wrong connector :p

The list below will show pin translations from the input (so the male connector attached to the car that originally powered the stock clusters), and the output (the male connector on the adapter itself that will plug into your March cluster)

On the driver's side the pin translation is like this:

_______|_INPUT_|_OUTPUT_|
-------+-------+--------|
GROUND_|___1___|___2____|
R LAMP_|___2___|___4____|
N/A____|___3___|__N/A___|
REV/FOG|___4___|___6*___|
SIGNAL_|___5___|___3____|
BRAKE__|___6___|___1____|


Passenger side pin translation:

_______|_INPUT_|_OUTPUT_|
-------+-------+--------|
GROUND_|___1___|___2____|
R LAMP_|___2___|___4____|
N/A____|___3___|__N/A___|
REVERSE|___4___|___6*___|
SIGNAL_|___5___|___3____|
BRAKE__|___6___|___1____|


* Pin 4 can either connect to pin 6 on the output (if you plan to have a red bulb as a fog light in place of a symmetrical reverse light), or you can run a cable from pin 4 (input) on the passenger side into pin 6 (output) for dual reverse lights. If you opt for dual reverse lights, then you can take the wire from pin 4 (input) and wire this to an external foglight, then splice the ground for that light into the ground wire (pin 1 input).

I hope to god that makes sense, please let me know if not.
 
Last edited:
Back
Top