ecu wiring

micra_pete

Ex. Club Member
please note i cannot be held accountable for any mis-types / in-accuracies on this list, you are responsible for checking before working

nats - not coil pack type

pinsnonnats.jpeg



101 injector 1
102
103 injector 3
104
105 oxygen sensor
106 fuel pump relay
107 ground
108 ground
109
110 injector 2
111 aac valve
112 injector 4
113 aac valve

1 power transitor (coil)
2 comb meter, n-cvt
3 resistor
4 eccs relay
5
6 ground
7 consult
8
9 cooling fan relay
10
11 n-cvt, air con, a/c relay
12 ign coil, injectors, air con, ign switch, fuse block - power
13 ground
14 consult

15 consult
16 maf
17
18 engine coolant temp sensor
19 oxygen sensor,

20 throttle position sensor
21 maf, tps, engine coolant temp sensor
22
23 consult
24 comb meter
25 n-cvt
26 nats
27 n-cvt, abs unit
28
29 maf, tps, engine coolant temp sensor
30

31 cam shaft pos sensor
32 comb meter
33 diodes
34 fuse block - power
35 neutral switch, n,cvt
36
37 tps
38 as 47
39 ground
40 cam shaft pos sensor
41 air con, duel pressure switch
42 n-cvt
43 power steering oil switch
44
45 air con, a/c switch, fan switch
46 fuse block
47 cam shaft pos sensor, maf, eccs relay
48 ground

non nats or very very early nats I

pinsnats.jpeg


101 injector 1
102
103 injector 3
104 fuel pump relay
105 oxygen sensor
106
107 ground
108 ground
109
110 injector 2
111 aac valve
112 injector 4
113 aac valve

1 power transitor (coil)
2 comb meter - tachometer
3 resistor
4 eccs relay,
5
6 ground
7 consult
8
9 cooling fan relay
10
11 a/c relay
12
13 ground
14 consult

15 consult
16 maf
17
18 coolant temp sensor
19 oxygen sensor

20 throttle position sensor
21 maf, tps, engine coolant temp sensor
22 cam shaft pos sensor
23 consult
24
25 n-cvt
26
27 ABS
28
29 maf, tps, engine coolant temp sensor
30 cam shaft pos sensor

31
32 comb meter - vehicle speed sensor
33 fuse box, consult, diodes - power
34 fuse box - power
35 neutral switch, n,cvt
36 ignition coil
37 tps
38 as 47
39 ground
40
41 duel pressure switch
42 n-cvt
43 power steering oil switch
44
45 cooling fan relay
46 injectors, fuse box - power
47 cam shaft pos sensor, maf, eccs relay
48 ground
 
so the differences are the following

nats non nats
fuelpump 106 fuel pump 104
ign 12 ign 36
cam position 31 canm position 22
extra cam position
signal 40

so if you can swap the wires about you should be able to use a non nats ecu on a nats car
 
nah, there is some other stuff too, nats can be removed , however i still haven't had my new ecu's made up for the later type so its pointless.

i would be half tempted to try the ecu wiring loom from a non nats car, but its a bit of work.
 
before people rely on the above there is quite alot of missing/wrong info.
 
please note i cannot be held accountable for any mis-types / in-accuracies on this list, you are responsible for checking before working

i haven't looked at this for sometime, if you want to add / correct ed please feel free, its done from a traces of the nissan wiring diagram
 
I dont have a NATS diagram so I am unable to be specific I'm afraid.
 
I wonder whats the difference with the Euro ECU's to JDM one's , the JDM ECU's looks a lot smaller in size. The post 98 models out of Japan have a different crank sensor for sure, have you guys checked the difference in the NATS and non NATS dizzy's ? so however you match the wiring the car is not going to start if the crank and cam signals are not in sync with the ECU.
 
wow a thread from the dead :eek: all the ukdm dizzy,s are the same zakie, and GA ecu,s work on ours with an apparently different optical disc (with 4 very thin 2deg iirc slots positioned radially)
 
All CG engines except 2000 on have the same crank sensor.
 
I have wiring diagrams for both nats and non nats ecus (pre coilpack). if you want them then send me a pm with your email address and il send them to you(Y)
 
I know this is an old thread, but can anyone help with a later model? I have a CR14DE UK car with NATS, but want to use a JDM ecu without NATS.
 
please note i cannot be held accountable for any mis-types / in-accuracies on this list, you are responsible for checking before working

nats - not coil pack type

pinsnonnats.jpeg



101 injector 1
102
103 injector 3
104
105 oxygen sensor
106 fuel pump relay
107 ground
108 ground
109
110 injector 2
111 aac valve
112 injector 4
113 aac valve

1 power transitor (coil)
2 comb meter, n-cvt
3 resistor
4 eccs relay
5
6 ground
7 consult
8
9 cooling fan relay
10
11 n-cvt, air con, a/c relay
12 ign coil, injectors, air con, ign switch, fuse block - power
13 ground
14 consult

15 consult
16 maf
17
18 engine coolant temp sensor
19 oxygen sensor,

20 throttle position sensor
21 maf, tps, engine coolant temp sensor
22
23 consult
24 comb meter
25 n-cvt
26 nats
27 n-cvt, abs unit
28
29 maf, tps, engine coolant temp sensor
30

31 cam shaft pos sensor
32 comb meter
33 diodes
34 fuse block - power
35 neutral switch, n,cvt
36
37 tps
38 as 47
39 ground
40 cam shaft pos sensor
41 air con, duel pressure switch
42 n-cvt
43 power steering oil switch
44
45 air con, a/c switch, fan switch
46 fuse block
47 cam shaft pos sensor, maf, eccs relay
48 ground

non nats or very very early nats I

pinsnats.jpeg


101 injector 1
102
103 injector 3
104 fuel pump relay
105 oxygen sensor
106
107 ground
108 ground
109
110 injector 2
111 aac valve
112 injector 4
113 aac valve

1 power transitor (coil)
2 comb meter - tachometer
3 resistor
4 eccs relay,
5
6 ground
7 consult
8
9 cooling fan relay
10
11 a/c relay
12
13 ground
14 consult

15 consult
16 maf
17
18 coolant temp sensor
19 oxygen sensor

20 throttle position sensor
21 maf, tps, engine coolant temp sensor
22 cam shaft pos sensor
23 consult
24
25 n-cvt
26
27 ABS
28
29 maf, tps, engine coolant temp sensor
30 cam shaft pos sensor

31
32 comb meter - vehicle speed sensor
33 fuse box, consult, diodes - power
34 fuse box - power
35 neutral switch, n,cvt
36 ignition coil
37 tps
38 as 47
39 ground
40
41 duel pressure switch
42 n-cvt
43 power steering oil switch
44
45 cooling fan relay
46 injectors, fuse box - power
47 cam shaft pos sensor, maf, eccs relay
48 ground
Do you no the pinout for a k12 by any chance ??
 
This fix is for the micra with the key with the red chip in it, and the non-coilpack engine with the single distributor.

Get an early ecu (the oblong one, not a square one) that fits your engine (either cg10 or cg13).

On the engine loom (so on the plug to the ecu) switch over these wires:
switch pin 106 to pin 104
switch pin 12 to pin 36
switch pin 31 to pin 22
switch pin 40 to pin 30

After this your car will not have an immobiliser anymore but you can still use your old keys.

you can send some thanks to https://www.paypal.com/paypalme/willemjacobdijkstra => I've spent considerable time on this, but would like to share the knowledge (unlike some!)


k11 nats to no-nats conversion.png



P.S.
If you have an australian car, you can just plug in a non-immobilised ecu and it will just work!
 
Back
Top