• Please only use these forums for blogs, they are not a discussion forum

Curtis' micra k10

15's i wanted 14s but im happy with them, 195/50/R15 not sure on make, but i plan to replace them anyway lol :D

Pick them up on wednesday
 
Ok webers will be off the car this weekend :( they will have a new home with daveeeee

Ill be having the cbr 600 bike carbs from him to try out :)

Just ordered:

Headgasket set
Cam belt

Hopefully some valves from sammohung

Gonna do the engine myself :D

Also ive got a video of the car driving past, not quick or anything, but you can hear the Rassp of the exhaust :D Will be uploaded either tonight or tomorrow...
 
Not sure yet, might start on stripping it tonight...

Picked up my alloys last night...there mint :D

Pics soon

z3ltu.jpg


345c3na.jpg
 
I think they have vauxhall centre caps in them so im gonna either buy some nissan or nismo stickers, or just take them off lol
 
CBR600 bike carbs on their way to me :D

Webers will be off tonight and packaged up ready to be sent off :(

The gasket set and cam belt should be here today so will make a start on repairing the damage

Also have to say THANKS to Sammohung :D he has willingly stripped a head and sent me a set of valves free of charge..! So Thank you! (Y)

WATCH THIS SPACE FOR DAMAGE PICS :(
 
Update!

Ok update

Stripped the engine down abit today, got the head off etc and the damage is pretty easy to spot i these pics lol

Bent valve 1

2h88px4.jpg


Bent valve 2

2504i2f.jpg


The bent ones

fyod9e.jpg


The gap lol

5lyo39.jpg


The cleaned up pistons

2vv2c5s.jpg


I cleaned up the vavles from Rich (sammohung) Thanks again (Y)

jsj6ol.jpg


So the car should hopefully be up and running next weekend with the bike carbs on :D

Picture of the bike carbs

2s611q9.jpg
 
no it jumped out of gear and it revved to ######y iirc

oh yer, here we are:
Loud music, not putting it into gear properly, putting my foot down to overtake thinking i was in gear, looked at the rev counter and it was past 8 and still going...long story short i made a mistake lol
 
i suppose with the head skim and the high lift cam and a worn cam belt some interferance could have been made, just seems a little unusual,
 
no, i wasn't just 8,000 it went PAST where 9,000 would be on the dials...

Bent valve vs standard

14nlc2s.jpg


The bent ones against a straight one

Straight one is on the left, they get worse, left to right lol

maiis8.jpg
 
curtis

i hope the ring,s are,nt trapped in their groove,s, from the contact (very common on our kart engine,s)
 
Those bent valves are wikid...Ive never seen them like this in the flesh

you're totally welcome mate...looking forward to you getting back up and running (with your new intake method too))
 
Cheer mate (Y)

tonight im gonna clean all the head up with some petrol and a brush, get it sparkling...then ill start reassembling, i just hope we have a dry day friday in Evesham as thats when i need to finish cleaning up the pistons etc ready for saturday

Things to do:

Get engine rebuilt, should be this weekend
Go to Ed and get a Rev limiter put in
Get locking wheel nuts off and alloys off
Fit new white alloys :D
Clean car inside out! (needs it)
Run it in (long cruise with no ragging lol)
Coilovers (if they are made)
Clean engine bay
Sort out side skirts
Re-weld exhaust manifold (not a very good weld that i did)
Spray dash black + other trim

+ more and more stuff
 
If i'd read this yesterday i'd have been thinking how the hell can you accidently rev it that high, but on the way home today i missed 5th gear and hit over 8500rpm lol. Luckily no apparant damage. (Apart from my ears, they were genuinely hurting from the noise lol)
 
Head is all cleaned up, gonna reassemble the new values etc tonight

Head should be back on tomorrow night then just leaves putting everthing back on etc and running in

Should be all sorted on saturday :D
 
Back
Top