• Please only use these forums for blogs, they are not a discussion forum

Chris' R34 Skyline GTT Series 2

hoodedreeper

Ex. Club Member
* Copied and pasted from the Skyline forum *

Time was drawing in closer for when i break my Supercharged MX5 ready to fund an R34 GTT. I wouldnt be a true car enthusiast if i wasn't already looking for cars on the interweb. My fingers were starting to hurt after refreshing various selling and auction sites here and Japan too often.

One car I kept being drawn back to was a white Series 2. It ticked all the boxes for what i was looking for, except it was the facelift front bumper that was preventing me from looking deeper into the details. So i messaged the seller and asked for a few more details and photos, very quick responses and the amount of photos asked on request was overwhelming.

Was it worth the 7hr round trip to go look at it, to potentially not like it? If it was as clean as it was in the photos, something major must have had been up with it if i was to walk away. Luckily this wasn't the case, infact the car was even better in person. After a test drive and a good poke around i really couldnt fault the car except for a knock on the driver side rear. So with an offer made he accepted and I drove away extremely happy! The 170ish mile drive home was faultless and i look forward to digging in and putting my own stamp on it.

It would have been rude to not get some photos, especially with the MX5

Nissan Skyline R34 GTT Series 2
RB25DET NEO 6
Manual Transmission

Imported in 2016 by IBE Cars in Huddersfield
Resprayed in original Pearl White in 2017

Its stock except for a custom turbo back exhaust, HKS mushroom filter and aftermarket stereo

27993577167_ee85b098cc_z.jpg


41051627950_35e977d196_z.jpg


28989657568_dd138bf8f1_z.jpg


42813885822_ee3990ec87_z.jpg


41961447655_5496acbdae_z.jpg


41961446205_b525f44e75_z.jpg


27993551437_a1164ea58f_z.jpg


27993550077_f83ff15af4_z.jpg


27993547757_00e7e98ac0_z.jpg


27993546277_fa1a8903d7_z.jpg


42144456354_f362e6f883_z.jpg


27993543017_caf3228edf_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Got the car back from H & S performance in Norwich who have done an amazing job on the Skyline

Oil Change
Spark Plugs
Fuel Filter
Japspeed Radiator
Thermostat
Drive Belts
Cambelt & Tensioners
Waterpump
Coolant change
Gearbox Oil change
Diff Oil change
Brake Fluid change

Meister R Zeta CRD Coilovers
Shorter front drop links
Wheel arches and suspension turrets undersealed

A-Tech 17" wheels back from powder coaters (done by SW Wheels) tyres swapped over and fitted along with new wheel nuts

Full alignment

Car drives completely different now and looks awesome!

42288265155_e773bc9dd5_z.jpg


29321084868_efb6e64e22_z.jpg


29321083088_6f82fee1f8_z.jpg


29321074218_aa484598f9_z.jpg


42474328274_7bc14d6338_z.jpg


42474325704_9ee767840a_z.jpg


29321072458_03a8e31735_z.jpg


29321070848_5a199ec1a5_z.jpg


42288250065_019a6224f6_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Why buy aftermarket clear side repeaters when you can just remove the orange lense yourself for free!

42778161514_d20a89fde9_z.jpg


With the purchase of the Blitz FMIC it was time to find an Altia bumper,this seemed abit more tricky than i first though. Luckily i found one only a couple of hours away, and it was en route on my holiday to Cornwall

41686892200_d45a93527e_z.jpg


While down in Cornwall we took a trip over to Devon and visited the guys and girls at Torque GT. They had the HKS SSQV Blow off Valve on offer, so would have been rude not to grab one while i was there. I also purchased a speedo converter too, which i'll get booked in with my local garage to get it fitted soon.

42778160864_4fc5ed8db4_z.jpg


With the car now serviced and the cambelt changed, i wanted to record the date like they do over in Japan. So i contacted Rajikaru who supply period correct japanese stickers, and they kindly replicated the sticker for me and have now added it to their store! I also purchased some other stickers to go with it.

42778160904_de051d4330_z.jpg


41686892020_4414da27cc_z.jpg


41686892090_a22c69eaa9_z.jpg


42590127895_3b1622781d_z.jpg


42778160474_2a9a287d63_z.jpg


We also got both cars out for a drive Sunday evening

42590127975_9306771f18_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
It was busy day for me and the fiance as we cracked on with doing little jobs on the car. Its those simply, low cost mods that make a little difference overall.

The engine cover got prepped and painted in silver. I was originally going to do it red, but thought it might have been too much, so kept with silver to keep it more factory looking. The text was painted red and i started to draw a black border with a sharpie but it decided to dry up, so that needs finishing at some point

41686891570_0ac94d5d7b_z.jpg


42590127405_b7575676f2_z.jpg


42778160364_3a318ac14f_z.jpg


The stock strut brace got a lick of paint too

42778159874_40b57fd2b9_z.jpg


I also gave the larger areas of the engine bay a quick de-grease along with the fitting of some red dress up bolts

42778160214_da5719622e_z.jpg


We also gave the calipers a lick of paint, you may have noticed a colour scheme going on...

42590127505_357bc96279_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
My second package from Japan had arrived, my replacement OEM steering wheel. This is fantastic condition compared to the one fitted to the car. The only problem was (and i didnt notice until i took the photos) was its actually from an Auto car, i didn't originally see the buttons in the advert on Yahoo Auctions,oops!

Before

44331553031_0a46c91183_z.jpg


After (before fitting)

44331553041_7b721f27c3_z.jpg


43615075504_b1145c89e5_z.jpg


Replaced the dash cluster bulbs to LED, photos don't do them justice. Just need to get a front interior light bulb to complete the interior

44331553481_91770681fe_z.jpg


44331553531_1de5ddaab8_z.jpg


My fiance very kindly purchased some LED tail lights and also purchased a personalised number plate along with my parents (i knew about the plates as i found it lol) for my birthday

44283608842_db6fe37cde_z.jpg


I had organised a photoshoot with some friends who have japanese cars, here are some of the solo photos i got of the GTT

43426277755_0c56659eb7_z.jpg


29395708637_6abe375c41_z.jpg


43426275495_32ac203095_z.jpg


29395705427_100dba3497_z.jpg


30464828068_1c2d9b8911_z.jpg


30464826608_c05f313b0e_z.jpg


30464824188_1dcf28ac76_z.jpg


30464835998_837239506a_z.jpg


30464823078_14a8fd30f3_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Not much has been happening and i didn't want to just post single photos.

Finally got the Altia bumper painted and fitted, along with some clear indicator units and chrome bulbs. Its transformed the front end and looks alot better! I'm glad i decided to colour code the centre bar and not left it black.

45009247611_c91ce1f2db_z.jpg


44290066244_18050695d3_z.jpg


The factory ceramic turbo doesn't like a bar of boost, most say around 11-12psi max is safe. After some research i decided to go for a Greddy Profec OLED boost controller to up the current boost a tad. Also hoping it'll come into boost smoother as its a little bit 'choppy'.

I didn't like the mount that's supplied so decided to make something. I started off with making a blank for the ash tray

44098103795_2598f7b04a_z.jpg


I wanted a flush look and have it removable if there was ever a problem or i didn't like it. We recently had some new magnetic phone holders come in at work so I decided to use one for the mount. I cut the ball & socket mounting off and was left with just the magnetic pad.

44290070324_fa234d8399_z.jpg


44098103915_c0f6574cdc_z.jpg


And stuck the other half of the magnet on the back of the controller

45009250221_8df3a664bb_z.jpg


With the hole drilled for the wiring it was ready to be 'test fitted'. I originally fitted a wiring grommet but I didn't take into consideration that it protruded above the surface, so scrapped that idea

44290069474_e1e6d3b04c_z.jpg


To make it secure onto the trim i used two small screws in the top corners. Double sided tape would have made it look cleaner, but I didn't want it coming off while i'm driving.

45009249751_db5e3fc7d1_z.jpg


45009249821_bcc9a5c666_z.jpg


45009249951_505c42094a_z.jpg


With it refitted it doesn't look too out of place in the cabin, quite pleased with the result! I've also fitted and wired up the AEM gauges from the MX5. I just need to fit the oil sandwich plate and sensor along with getting a boss welded into the exhaust for the AFR gauge.

44290070044_3788cda29d_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
In August I ordered a new set of wheels, I wanted a set of these for the MX5 but they don't make them wide enough in a 15. So i'm very happy to be able to have a set on the Skyline

45087175592_f906af7d27_z.jpg


45136230051_63c257a603_z.jpg


Choosing a wheel design was difficult enough, let alone deciding which fitment to get. I decided on 18x8.5 ET30 and 18x9.5 ET30, playing it safe due to the arches are original and mint, would be a shame to ruin them because of the offset being lower.

I believe Nismo recommend this fitment for the GTT, so that was some reassurance :)

Colour choice was also another challenge, the current bronze wheels look awesome against the pearl white and I had my head set on that. But then i saw the GT Silver was an option and well....you can see from the photos that i made the right decision (or did i?)

45087175462_b7c5e72294_z.jpg


This is one of the rear wheels to help show the concave, the fronts are alot more straight spoked due to the width

30198306717_9a3bab4f4c_z.jpg


I wont be getting tyres for a couple of months, show seaon is over here in the UK and the car won't be driven much when the salt starts to be spread in the coming months.
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
With the bodywork being in mint condition (except the difference in colour on some panels due to the pearl) my attention would be under the bonnet. I can't afford a full forge build,top mount turbo etc so went for a cheaper route. I've been collecting parts for a couple of months and now I'm at a stage where i can post about it.

30428195567_5723c3801e_z.jpg


Stock Turbo Stage 3 Hybrid (spec below) (Rebuilt by Universal Turbos)
Genuine Gasket Set
Apexi Power FC
Z32 MAF
R35 GTR 570cc Injectors
Walbro 255 Fuel Pump
Blitz FMIC
NGK BKR7E Plugs
Splitfire Coilpacks
Competition Clutch Stage 2 (supplied by Conceptua Tuning)
Lightened Flywheel
Braided Clutch line

31492379798_6f8749d36d_z.jpg


30428195727_701e8a2091_z.jpg


31492380118_0f193bf459_z.jpg


Re-Profiled Compressor Cover
T38 Compressor Wheel
360 Degree Thrust Bearing
T3 Billet Backplate Modified
T3 Bearing Housing Modified
Hi-Temp Turbine End Piston Ring Seal
T38 Turbine Wheel
Re-Profiled Turbine Housing
Ported Wastegate and Larger Poppet Valve
1 Bar Actuator
Up-Rated Actuator Bracket

My aim is 400hp,would be over the moon if it was more :)

I also have a Tomei turbo elbow on order through Nengun Performance
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Nothing happens for weeks and all of a sudden everything happens at once lol

The new tyres for the Work wheels arrived and i didn't waste any time getting them mounted and fitted to the car. The front ride height is left untouched from the 17s, the rears were raised 20mm (its still veeeery close to the arch lip)

I think playing it safe with the offset of 30 was a wise decision, it may not be the 'fitment' that kids nowadays wanna see, but i think its perfect :)

Not long after purchasing the car, i already had a vision of what i'd like the car to look lilke. My very first car/project was a red Nissan Micra K11, one of the things i loved about that was the Nismo livery. That car taught me alot of cars in general especially thinking outside the box when it came to modifying. I knew the livery would work well on the R34 so it had to be done.

45488441402_d071b53850_z.jpg


A big thank you to Unique Signs & Graphics in Norwich for designing it all from scratch and for fitting it. These were also the guys who designed and fitted the HKS livery on my MX5

31665548038_d69b47c5f0_z.jpg


45487662702_5580377efd_z.jpg


31665540778_5d79db2b91_z.jpg


31665536188_ea5902c68d_z.jpg


44624150885_7877261207_z.jpg


44624148965_30bc9b7c74_z.jpg


44624143905_51206eaa22_z.jpg


44624147085_1c1373f76c_z.jpg


I also tried out some coloured smoke grenades, I'll be having another go at night at some point

44812617324_5a0f6c09ed_z.jpg


44624156425_89f17c44ab_z.jpg


44624160665_bced65ec2c_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
A small update to catch up over the past couple of weeks

Took some autumn photos

46397122351_55553e2d8c_z.jpg


31457443077_ab1dcfcde6_z.jpg


46397123921_eeca017e5d_z.jpg


46397126311_29ef02a646_z.jpg


My Tomei Exhaust elbow arrived from Japan via Nengun. The quality and workmanship on this is incredible!

45673585194_b5f53ecb5e_z.jpg


45673585244_6d04ce53cf_z.jpg


I found these on Yahoo Auctions and JDMParts Rupewrecht arranged the purchase and delivery. Originally they had a 2-3 week production time as they're made to order. But these were ready to be shipped within a week!

The quality is very good, the pieces are quite thick so not thin and flimsy like some carbon/FRP parts. They've certainly got some weight to them!

45673586804_358319f3e0_z.jpg


31457409427_e7a6d8a02f_z.jpg


45673586684_29e341fb86_z.jpg


45673586654_31ba7ec025_z.jpg


45673586714_f5f63f7324_z.jpg


45673586884_421a0f7201_z.jpg


A friend of mine is currently cutting out the engine cover text aswell as the fuse box diagram to help keep them looking 'OEM'. Plus it breaks up all the carbon
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
We headed over to Blickling Hall here in Norfolk, they had an arrangement of lights for the festive period which was a great photo opportunity

32976043738_dc076b37c7_z.jpg


46851475581_5438201dc3_z.jpg


The LED lights had produced an intermittent fault. The first set, the outer tail light ring was missing half of the LEDs and the second set of lights had an issue with the brake light occasionally not working. Driftworks accepted a return and arranged the refund very quickly, I can't fault them for that. The OEM lights were refitted, i think i prefer them lol

31910153657_c0e0f4c19f_z.jpg


Although the interior was clean looking and stock, I felt it needed a lil bit more. I had a Nardi Deep Corn steering wheel stored away from the MX5, Driftworks supplied a HKB boss kit and the Nardi was promptly fitted.

32976046648_e4233c818e_z.jpg


32976046568_1496f7662d_z.jpg


Upon fitting the boss kit and testing it, i noticed something on the floor mat. I had only gone and snapped the locating pin on the clock spring....****! I removed the hicas fuse to temporally disable it until i could sort it. I had a couple of options, replace the clock spring and potentially have it happen again or delete the hicas.....which brings me to my next update

Driftworks Hicas Delete

32976044528_dfb9e15360_z.jpg


H&S Performance took care of fitting the kit and aligning the car, as always they've done a fantastic job!

46851476041_b047cde48c_z.jpg


Last photo of this update is one i took this evening as the sun was setting, no real reason just a random photo. Its also the first using my new photography watermark teaming up with

Modificata Culture

32976039738_60be6b5f34_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Small update

Fitted a tsurikawa and a hannya omamori to the 34

33096135948_f77ea63fba_z.jpg


33096137758_ae984bfbd3_z.jpg


46247290184_932f94840f_z.jpg


I've finally got fuse box diagram sticker fitted, it finishes off the carbon a treat

46247287194_a969b85e75_z.jpg


46247285694_a7f4bc84f7_z.jpg


46247283134_35e14593cd_z.jpg


32030579897_c405cb899d_z.jpg


While the camera was out I couldnt help but take a few more photos

46247292914_e552b8d5a3_z.jpg


46919759212_89a38223ab_z.jpg


40007092153_599d795cd5_z.jpg


32030581037_26b1efca04_z.jpg


32030578817_d67992ac3f_z.jpg


32030577837_3f14722615_z.jpg


33096140268_4751e7e186_z.jpg


33096138388_b92d82fcc9_z.jpg


33096135088_1edac0f87f_z.jpg


40007073843_dc8d3725b5_z.jpg


33096131628_9bc3ae5845_z.jpg


40007071573_13a47388bf_z.jpg
 

Low Rider

Poindexter
Founding Member
Moderator
Club Member
Those HKS SSQV's are pretty loud, I swapped mine out for a Turbosmart Vee Port Pro on the Micra at the risk of lacking in JDM authenticity.

Coming along nicely though, definitely deserves a filter upgrade along the way :)
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
46252404505_b9c3ac486f_z.jpg


After reading up on a Speedhunters article by Jordan about his RS4 audio upgrade, I was that impressed I decided to bite the bullet and treat myself to one too.

40201570323_13781e62f0_z.jpg


The DMX7017DAB is a double din mechless unit with a large touch screen display. The minimal buttons along the bottom edge gives it a more modern look without distracting you much.

It has the bells and whistles you expect to find on a modern aftermarket stereo like DAB, Bluetooth, rear USB, steering controls etc. What drew me to this was a couple of things. The first being the integrated dash cam.

46252405885_31888e6350_z.jpg


With the dash cam plugging into the back of the unit, you can view the Camera aswell as play back recorded footage and photos. The camera has a built in shock sensor, a message promptly appears if the car has been hit in your absence, and you can review the footage straight away.

40201576113_32e6260d33_z.jpg


The second feature that I loved was the ability to mirror what my phone does. For Android an app called Android Auto is required. This allows you to mirror Google Maps/Waze onto the stereo, while still being able to listen to Spotify/Google Music and make/receive phone calls! Very handy for those road trips or convoys to car shows

46443059204_f323c0f24c_z.jpg


Another feature the Kenwood unit has is a reverse camera. You can pick up a generic camera off eBay or Amazon for not a lot of money but I didn’t want the extra grief of splicing and hoping the built quality would last. So I went with Kenwoods unit and I’m glad I did. Direct plug and play and all I had to do was splice into the reverse light loom

47166444791_a16d70be79_z.jpg


I finished the install when darkness fell so I’m eager to see the quality in the daylight :)

47166446341_121205b6c9_z.jpg


The rear speakers have been crackling for awhile so this was one job that needed addressing more than anything. I didn’t know what I was letting myself in for until I was half way through it…

32224645157_7890bdd89c_z.jpg


The rear seats, door cards and trim had to be removed before I could touch the parcel shelf. The parcel shelf area was covered in a black dust, thinking it was the parcel shelf material disintegrating, I was wrong.

32224645127_c4a7b48689_z.jpg


As you can see, there wasn’t much left of the stock Clarion speakers, no wonder the sound quality was so poor! The new speakers dropped in a treat and I managed to reuse the original fixings. At the point I wished I had bought the wiring adapters but nevermind.

40201586863_9b04c6d776_z.jpg


47166454471_3bc2b9d064_z.jpg


With the rear interior put back together it was time to tackle the front speakers. This was ALOT easier, a few trim clips and screws and access was easy. Luckily the front speakers already had the adapters (weirdly enough) so that was plain sailing.

32224636737_0a0af0a276_z.jpg


I did buy some sound deadening pads to put on the inside but space is limited and daylight was becoming less and less. I’ll tackle this at a later date.

The last thing on the list was to install the slim subwoofer. I was hoping it would fit under the seat, but upon removing it I didn’t realise the centre is humped and tapers down. So I decided to put it behind the seat instead.

46252408795_6ebd747ba7_z.jpg


The wiring is a lot simpler, all of the wires go into a single plug, none of those nasty terminal screws we had ‘back in the day’. The hardest part was routing the live cable through the bulk head (wheel and arch liner off and it’s straight forward from there)

So there we have it, a full multimedia upgrade! I still need to play around with the equaliser, then I’ll get a video sorted
 
D

Deleted member

Guest
Sorry for asking such a pointless question
But your little charm hanging from ur rear view mirror
May I ask were I could get one
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Not long after I purchased the car I used the Turtle Wax headlight restoration kit. Unfortunately it didnt last long before the lights became cloudy again. I got recommended by a friend of a mobile company who do them for a very reasonable price. So I got the car booked in and well....the photos speak for themselves!

46679488705_136b19f781_z.jpg


46871020074_ef70a03a82_z.jpg


46871020064_856a471042_z.jpg


Since the Nismo addiction started I've been on the hunt for an S-Tune boot spoiler. As you can imagine these are rare as rocking horse **** and near on impossible to find. I found a company in Australia who makes a copy but its no longer available.

40628999773_66a5e87bf3_z.jpg


40628999583_fcf8e25872.jpg


I did find one on Yahoo Auctions, but it came complete with the spoiler blade and the price landed was £800+

I happened to see a post on the Skyline Owners Forum facebook page about someone's own design for some spoiler legs. Messages were sent back and forth for a lil while and I made a purchase.

His friend was developing some covers but there would be a delay due to finishing the mould, getting orders etc. I went with the Carbon Fibre option, who doesn't like carbon?!

These took approx 4 months and they landed on my door today (12th April). The delay was due to the raw and painted versions being made and delivered first before the carbon versions got put into production.

Fitting was quite straight forward as its all been moulded to the underneath of the OEM spoiler,so it fits like a glove. The spoiler bases have adjustment so you can put it where you like (within reason)

47595035781_7653ef6e3c_z.jpg


47595035641_d908cd9822_z.jpg


40628914683_b3887f3f4e_z.jpg


47595035081_246b60730b_z.jpg


32652535047_08af83af30_z.jpg


32652534627_7b14594d19_z.jpg


46870944234_f3e4a856ed_z.jpg


46870943964_c3c0a45f92_z.jpg


46870943484_7d2f913128_z.jpg


46870943024_8ff4ca4216_z.jpg


46870942634_592bd36018_z.jpg


46870942324_09dc810f54_z.jpg


46870942054_c273cd1d70_z.jpg


33718004778_2d944cc7df_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Hanami is one of THE most beautiful things on this planet, and I'm extremely envious and jealous of the Japanese and this beautiful season. With my social media exploding with various images of this iconic scenery, I knew I had to try and replicate it as best as i could.

In the UK its a relatively small window when the blossom is in full bloom and how long it lasts for (also adding a lack of spare time to get such photos) makes a good challenge. I spent a couple of weeks driving round the city trying to find the perfect backdrop, this was harder than I thought.

I finally found somewhere good enough and I did my best with what I had

46808830335_54fa466c3a_z.jpg


47725344441_84109f729d_z.jpg


46808825555_f423838e99_z.jpg


47672282402_7a7127b23f_z.jpg


I've been going to a car show called Modified Nationals for the past 11 years. This year it moved date and location which ended up being scorching hot and a far better surrounding, win win!

46808834315_57d91f24d5_z.jpg


47725348941_99e9c515c5_z.jpg


40758747793_bc6d86a8f4_z.jpg


32781934527_de2971229c_z.jpg


Myself and a couple of others have started our own Cars & Coffee meets and today (28th April) was the first meet of the year. The weather just about stayed dry for the majority of the morning, I was met with a couple of more R34s

32781946857_88554411c9_z.jpg


32781945117_3bd4af4885_z.jpg


Seeing this V-Spec 2 Nur roll in made me go complete fan boy. You just dont get to see this car out in the 'wild' very often.

47725358251_4d503c44db_z.jpg


The full album can be seen here > https://www.flickr.com/photos/93923515@N07/albums/72157708154531655
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
I've been looking at replacement seats for a couple of months but have always been undecided on which ones. Last week we took a visit to GSM Performance to consult with the sales team on various seats and to try them.

47960622478_8cc8e1ab15_z.jpg


Being a 'bigger build' comfort was top priority, and trying the seats out before commiting was a major advantage. It was a tough decision as there were so many nice seats,but in the end I went for the Recaro.

47960550996_46a66db268_z.jpg


I managed to source some R34 GTR Bride rails that had been modified to fit the GTT. Upon ftting I noticed the Recaro seat mounts were alot wider than the rail. Several hours of swearing later, I had some brackets made up and everything bolted together.

47960552561_bcd12b424c_z.jpg


47960511682_ea6b5ed98d_z.jpg


47960513682_a3ee68c17a_z.jpg


47960510422_80f54098e8_z.jpg


I'm unsure if the GTR seat rail is different height wise, but the seats do slope down which has changed the driving position abit

47960524058_09eccae4e5_z.jpg


47960508987_73c2b8ab19_z.jpg


47960506542_5bde37395d_z.jpg


One feature I really like is the reclining lever that's neatly camouflaged into the harness cut outs.

47960545726_e3f6c8126b_z.jpg


The suede centres make the seats pop alot more than the all leather equivalent

47960505507_c59cf9c40f_z.jpg


47960519173_08e04a0c57_z.jpg


47960518688_e27cea34a7_z.jpg


47960503887_09a30c9dce_z.jpg


47960543391_b335daefcc_z.jpg


Its abit snug inside, the side bolster does currently touch the doorcard. I'm hoping I can modify the mounts I made to bring it over abit.

47960517443_7529b2b660_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
After 24hrs the seats had marked the doorcards quite badly, so I had to sort them out ASAP. I removed the doorcard to have a look, hoping I could modify and retrim the arm rest. But upon a closer look the whole door card would need re-doing and I didn't really fancy all that work. So I adapted the rail mounts instead.

I started with the driver side by drilling another hole next to the first one, the seat was still hard pushed against the doorcard. To explain it briefly it required alot more moving over than I first thought. The bracket on the rails was fouling the bottom of the seat so those had to be cut off. The belt buckles were too short to be bolted to the rear inner rail mounting hole so additional brackets had to be made. Then it was a headache trying to hold the seat up to get said bolts in while holding the seat up to line it all up while making sure the belt buckle didnt fall down.

*sigh*

But I finally got it all sorted and theres still room between the seat and the centre console.

47960517443_7529b2b660_z.jpg


48032511582_712bc8a4e9_z.jpg


With the seats in I have to admit it was abit of a struggle getting out without brushing against the steering wheel. I decided to go with a quick release steering wheel, but it had to be a slim version. A friend had a Vac Motorsport race quick release for sale which would do the job nicely. The centre of the quick release boss looked too small for a horn button, so he included some Fast and Furious-esque NOS buttons to use as horn buttons.

The Nardi deep corn wheel has served me well in pretty much all of my cars, but it was time for it to retire in favour of a smaller, more modern equivalent. I decided on the Sparco L360 in leather, mainly for its 330mm size and it's flat bottom.

48032511757_5f8a510fac_z.jpg


Of course,this wasn't going to be an easy job, not with my current luck lol

I wanted to mount the horn bracket inbetween the HKB boss and the first half of the quick release. This was to make the wiring neater and hidden. The first half uses a Nardi bolt pattern (whats the problem with that you ask?)

Well...the horn button bracket uses a Momo bolt pattern. Even redrilling the bracket would make it lean over to one side and not be central. So the only way was to mount it between the second half and the steering wheel. Luckily theres a gap between the two brackets, the wires were heat shrunk and taped to neaten it all up.

48032511657_9ee0df0fd0_z.jpg


48032401081_4dbf42a5b4_z.jpg


48032444538_a1af50f039_z.jpg


48032511822_ef1697a000_z.jpg


Once it was all mounted together, I lined up the supplied horn button from Sparco and it fits :/ Just my luck lol
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
In the future I plan on getting the interior trims skinned in Carbon Fibre. I've decided to paint them instead for the time being. I wanted something subtle but eye catching if seen in the right light.

White would have been too much and so would Red, so I decided to go Black, but which one? Working in a Motor Factors it was a bonus to have a rack full of aerosols, along with being able to mix paint if need be.

Ford Panther black has always been a favourite,so it was an easy decision

48082193997_67398d1f1e_z.jpg


48082129508_1d4101c789_z.jpg


48082129638_26b289c7e3_z.jpg


48082193752_2ed7b34e48_z.jpg


48082094711_4572efeb0d_z.jpg


I really need to sort out the lower dash trim to get rid of all of the scratches from the stereo. I can get a brand new one from RHD Japan for £130 + shipping + import, but its not an urgency just yet

While I had everything out I replaced the cig lighter bulb for an amber version. This now matches my ignition barrel light (photo further up)

48082193862_2a023ef7c2_z.jpg


This was also the perfect opportunity to swap the bulbs in the climate control for a better quality LED. After several recommendations these were purchased from an eBay seller in Australia

48082193702_0d5dc6e61e_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
June is Prom month for alot of students, I was thankful to be asked to do a couple (only have photos of the first one). It was great to help out fellow Skyline lovers, hopefully see them on here in a few more years time lol

48397520107_05059a4aeb_z.jpg


48397380186_cffa0c2071_z.jpg


Me and Lu took a drive out for a bite to eat, ended up doing a 100 mile coastal drive around Norfolk, oops! Managed to stop at a couple of places for a snap

48397380076_1d13533c0a_z.jpg


48397379951_8389f466bf_z.jpg


48397380006_b3868618f6_z.jpg


Every year Myself and a group of friends organise a charity car meet raising money for The Big C Charity and East Anglia Air Ambulance. On the night we raised £1300 and we still have a raffle going for another week or so. Here's a photo from the night

48397287926_3749a749d2_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
I've been looking for a rear tow hook for awhile but couldn't find one I liked, so I made one

Using the original one as a template, I extended it so it would be visible underneath the bumper

48397301631_b705135384_z.jpg


The original is a 2 skin pressed piece with a bracket on the side. Mine is made from 6mm steel sheet, I understand its not as strong but I don't intend on using it for towing, its purely for aesthetics

48397301481_ec584c3e2c_z.jpg


48397441747_9efce657cb_z.jpg


48397301841_b388529fe7_z.jpg


We've recently had some thunderstorms (doesn't happen all that often) I was lucky enough to grab this photo while out at a car meet

48397301201_274d1f042d_z.jpg


Which kinda brings me onto my next update, this weekend just gone at Silverstone Classic. I went along with the GTR Drivers Club, it chucked it down with rain most of the weekend but it was still a great weekend. Nissan UK and Nissan JPN supplied the hospitality along with loaning us a 2020 Nismo Model along with their GT-R50 prototype. Seeing photos of this online I didn't like it, but its not quite as bad in person lol

48397285666_d5d41a2096_z.jpg


48397284901_db053bdb55_z.jpg


48398107557_02a98e59a4_z.jpg


48397964326_91f52c876f_z.jpg


48397946076_b1a005ddf8_z.jpg


Next stop.....JAE in 2 weeks time
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Its been a busy month or so, I've been waiting to build up enough info/photos to make it worth while posting.

The first package to arrive was from Japan. I've been wanting to try it for awhile now so I bit the bullet and ordered some. Its an expensive way to drink coffee but oh so JDM

48576715306_716bf70ae8_z.jpg


The next one original came from Japan but was shipped from within the UK. Garage Sweet Tooth stock some really cool authentic parts and clothing. I wanted some more accessories to go with the hannya omamori and the tsurikawa handle and this new-old stock coin holder caught my eye. Still waiting to get some coins before I fit it so i'll save that for another update

48576709431_5358999e17_z.jpg


Next was an item I spotted in the Garage Sweet Tooth shop, but they didn't have the type I was looking for. I dropped Josh at Torque GT a message to see if they had any Electronic Toll Card Readers kicking about, luckily they did! A couple of days later it arrived and I didn't waste any time fitting it. I only wanted one because it talks haha. Videos are better than photos so heres a short clip



With my 30th birthday approaching my fiancée asked what I'd like, I suggested a 1/24 scale model kit of an R34 so I could make a replica, but it wasn't as straight forward.

Because mine is a 25GT with an Altia front bumper, this meant two kits had to be purchased and blended together. Luckily my friend Tom at Waltonstyle does custom Hot Wheels so he offered to lend a hand to sort it.

48622535486_2b913254b2_z.jpg


48622535091_b906bd17ef_z.jpg


48622535066_7bc7709e9c_z.jpg


With the shell now complete it was ready for paint. Working in a motor factors I have access to mixing paint. Tom also makes custom water transfers and was able to make the Nismo graphics

48622681747_19dfd9e6f1_z.jpg


48622682012_25e3f3f65c_z.jpg


Miniature Recaro Sportster CS seats came from Australia, some photos of the interior too

48622681612_2163d33076_z.jpg


48622535381_fe68effe47_z.jpg


48622181683_0b818d4410_z.jpg


Some photos of the shell nearer completion. Tom even made the Pistonheads logo,Nismo badge and number plate for me, some nice attention to detail

48622181833_b9472db24a_z.jpg


48622181778_ab42389441_z.jpg


And here's the finished model, complete with Work Emotion CR Kiwami

48622682157_fc4cec8434_z.jpg


48622535756_714816a9f9_z.jpg


48622535566_15c0fc1c0a_z.jpg


48622181598_1e6d87ebd3_z.jpg


48622535576_4c76a8fe29_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Got some good and bad news :(

The bad news is, the engine upgrades that I've been storing will be on hold for awhile longer :(

The good news is, I'm getting married! So I've now got a year to organise that which to be fair most is already sorted. Followed by a honey moon in Japan in 2021! (I think I'm more excited by that to be honest hehe)

The front bumper needed to be resprayed under warranty, which was the perfect opportunity to fit the Blitz FMIC

48576708966_41ae34af66_z.jpg


48576708686_e2df56e0fd_z.jpg


Gave the pipe work and chassis areas a coat of paint

48576860132_eebed1171e_z.jpg


48576859827_de4b65ca83_z.jpg


48576860207_90eea46dde_z.jpg


48576708266_ab006aee20_z.jpg


48576859932_17ec7338f4_z.jpg


The reinforcement bar had to be cut/modified to fit around the intercooler, which wasn't alot of work to be fair. I also replaced the blue silicone hoses for black ones along with mikalor clamps

48622181538_2de682e294_z.jpg


The horns had to be relocated, so I swapped them for some new ones

48622535111_31cb6e131e_z.jpg


Stainless fixings and bolts replaced the original rusty ones

48622681912_36812ea871_z.jpg


The bumper went back on about 90% right. I think the intercooler is still fouling it ever so slightly so that'll need adjusting/trimming again

48622535561_2da6f8dc08_z.jpg


48622181753_15540c6b42_z.jpg


48622681642_8f90e2c1e1_z.jpg


48622181483_3ef8c9d1aa_z.jpg


48622681562_a10856d315_z.jpg


I also removed the window stickers

48576861167_0e0151b9c3_z.jpg


48576709236_50a51cb26c_z.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Time for an update!

The biggest announcement being I'm going to be a dad! Woohoo! Its due to arrive 6 weeks after the wedding which is gonna make our summer very busy!

49611034742_f6052dea89_b.jpg


Bought a new camera lens, a Canon 35mm f/1.4 so gave the car a clean to test it out

49610248998_ddf422ca98_4k.jpg


49611020072_0122b3b792_4k.jpg


49610766451_c03ebe3948_4k.jpg


49611019912_edcf07eb22_4k.jpg


49610766226_d81012f0b5_5k.jpg


49610766146_e4bdddae34_4k.jpg


49610766091_6566a9ef2d_4k.jpg


49610248278_198b57d17f_4k.jpg


49610765811_b52c3a5bd9_4k.jpg


49611019247_5101a60577_4k.jpg


A few weeks ago we went for a B road blast, came into a small village where the already narrow road became alot narrower. I moved over to pass some cars and ended up hitting a hidden curb, not with one wheel....but both :(

49611034527_106b23a3bb_b.jpg


49610781366_1ce68c45a2_b.jpg


49611034657_e0cee02e10_b.jpg


Immediately took it to a local Wheel Refurb company to get a quote. They've done a tester and although they can do a shadow chrome finish, the front face will be darker than the factory finish. I've decided i'll get all 4 re-done so they all match. Not what I needed, but hey ho thats life

I've been wanting to head into London to take some night photos of the car, following a few photographers on Instagram certainly boosted the idea. With the ULEZ charge paid, it was time to travel 2.5hrs south west towards the concrete jungle. With the city being so busy I knew we had to get there late to help avoid heavy traffic.We arrived in central london at 10:30pm and started the tour of locations I had saved on my phone. The mirrored Google Maps on my CD player certainly made things easier rather than being glued to my phone.

49610264068_b7fb33a518_b.jpg


Having never driven through London it was an all new experience but it wasn't too bad, I envy those who live or commute to the area. After a few wrong turns and driving around the block a couple of times I finally found one of the main locations I wanted to stop at.

49610350903_4b98887766_4k.jpg


Seeing super and hyper cars driving around as if they were your normal run of the mill cars was certainly a sight worth seeing. As we pulled over behind Harrods, a Mercedes G Wagon rolled past with the reg plate G 63, if that doesn't shout expensive I don't know what does lol The city was littered with AMGs of all varieties, lambos, ferrari's and bentleys. Not many other modified cars which was a shame.

49610350783_3d079ccec2_4k.jpg


Sloane Street was one of the main places to see those cars, although I think its quite over hyped after being there a little while.

49611122747_ca4acc5192_5k.jpg


49611122432_9deecff9ee_3k.jpg


The last location we wanted to stop by was The O2, this place is a common location (overused in some photographer's eyes) but I wasnt going home without stopping by. With Canary Wharf lit up behind it makes a fantastic background.

49611121327_0cb007a187_3k.jpg


49610867376_afba623d80_5k.jpg


The other half captured this photo which was pretty cool

49611123027_012c25541e_4k.jpg


It was a loooong night, we didnt get home till 5:20am and I had a photoshoot booked in a few hours later, oops!

With London out of the way, it was time to search for some daily wheels. I went with some 18" 350Z Rays which really suit the car IMO. The supplied tyres were at the end of their life, a friend hooked me up with some Avon ZZ5s on the cheap

49610781201_307e3cfd08_b.jpg


49610264023_16106b1366_b.jpg


49610264068_b7fb33a518_b.jpg


That concludes what's been happening as of late. Show season is round the corner so I'm looking forward to getting out and expanding my photography portfolio
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Awhile back when the bumper got repaired due to a paint defect, I wanted to cut the bumper and open it up but the bodyshop wanted too much money (I thought they were painting the whole bumper under warranty, but they werent) So i decided to go ahead with it now. The bottom piece isn't completely flat, to do that it'd need spraying so it'll do for now. While the bumper was off it was a good opportunity to get the bumper to fit better, luckily the piece I cut out was what was causing the issue.

Purchased an intercooler stencil from eBay, looks pretty good IMO

49687573983_4da7ee4e20_b.jpg


We sell bumper mesh/grille at work, although its slightly smaller than the OEM mesh, its not far off

49688412102_afeb13b04e_b.jpg


I also ordered a smaller number plate which looks sooo much better :)

49688412257_a6daa407c9_b.jpg


I've been eyeing up the Nismo B pillar garnish for awhile, but couldn't bring myself to spending £150+ on some stick on carbon. It wouldnt be too bad if it was a whole replacement piece, its worth the money then. Again, my work came in handy as we sell 3D carbon wrap so gave vinyl wrapping a go. A friend cut the logos for me, fake it till you make it lol

49687573923_31189096f2_b.jpg


I've also seen some GTTs with a spoiler garnish, it can be seen in the Nismo parts catalog too. I've only seen 1 set of brand new ones on Yahoo Auctions and they sold for £450 + shipping + import duty (thats approx $525) which is ALOT for some gel covers.

49688520967_950977da07_n.jpg


49687573893_f11bf3aacb_b.jpg


So the carbon vinyl wrap came out again and I made a template of the spoiler ends and transfered that to the vinyl. Its not perfect but can always be re-done at a later date

49688108281_6b49310c84_b.jpg


49688412142_0d3605d79f_b.jpg


I ordered some Nismo clear indicators from RHDJapan, first time using them and it certainly wont be the last. They were dispatched from Osaka on the Friday and delivered to me on the Monday!

49687573878_f7114f4ef2_b.jpg


49688107986_69ae1f2c03_b.jpg


49688107971_4d8f9259c7_b.jpg


There's been some minor difficulties with shifting 2nd > 3rd and sometimes into 5th. The clutch doesn't slip but after a search on the forums people point to the shifter being at fault (mainly the Bush)
Alot of people have recommended an Australian company called Cube Speed. Coincidently Speedhunters recently had their contributor Ron post up with the same issue, and fitted the same kit.

49688108651_f6b1265552.jpg


49688412722_9078607961_k.jpg


49688412772_afa0c3a6ae.jpg


I went with their Premium kit to allow adjustment on the return spring. Fitting was relatively straight forward with everything access able from the top. To fit the return springs you need the car in the air as they're a bastard to get to.

49687574553_7e1c02a232_k.jpg


The feel of it now is incredible, it's transformed the drive of the car completely. It's alot more mechanical, albeit a slight notchy feel but that's probably down to the Shortened throw now. 2nd > 3rd is now effortless.

I've made a very basic video on my phone and uploaded it to YouTube



I have another update to post so expect that within the next week :)
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Following on with the Nismo theme

JDM Parts Rupewrecht assisted again with bidding on an item on Yahoo Auctions, this time a set of sales brochures and part catalogs inc Nismo and Tommy Kaira

49704372036_1739a67454_h.jpg


Trying to keep things period correct as much as possible, I was on the hunt for a mid logo gear shifter to company the new Cube Speed short shifter. I managed to find one under half the price of a new one someone had offered.
49704687827_95cb6d6737_3k.jpg

49704687607_0b86424777_3k.jpg

We sell a leather cleaner and restorer at work which should bring it back to life. After a scrub with hot water and washing liquid it was time to get messy with this stuff
49703842543_a0afb5ce71_3k.jpg

The photos don't show much difference, but in person its made such a difference :)

49704372251_53c3bf088a_4k.jpg


49704687607_0b86424777_3k.jpg


49704372141_4872584d70_4k.jpg


49704687427_a1776510bb_5k.jpg


Another Nismo part I've been wanting for a loooong time were the tail lights which got discontinued years ago, along with the Sun Line Racing equivalents. Alot of people suggested ZLED but I'm not 100% sure on the GTR Style lights, I much prefer the individual LED style.
I was browsing through Facebook and spotted a post on a Supra page by a company called Daniel Man's Custom Lights. I messaged Daniel with what I'd like and he was happy to give it a go. I sourced a spare pair of light units and got them sent straight to Daniel.
A week or so later and they arrived just before the country's lock down for the Covid-19 pandemic (please excuse the dirty car!)

49704695547_263bb16607_b.jpg


49704379736_d5bdda80e6_5k.jpg


49704379226_976892f581_4k.jpg


49704695012_4454c123c7_4k.jpg


49704695242_a54ee083d2_5k.jpg


49704695432_4523332b11_3k.jpg


49703849218_18f96071fb_5k.jpg


49704695692_d4aa89d288_5k.jpg


A couple of front shots while I was there

49704379056_03df1abf95_4k.jpg


49704379161_45a7a16cf6_4k.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
With the Covid-19 lockdown,finding things to do has been quite tricky. I decided to give the engine bay a much needed tidy and spruce up. I saw some photos of a strut brace refurbished in a wrinkle type paint which got me thinking.

I thought of using truck bed liner paint and a quick google took me to a brand called Raptor made by U-Pol (my work is a U-Pol stockist, not that we'd be able to order anything at the moment). I dont have access to a spray booth or a unit so the 'proper' stuff was out of the window, but they do do an aerosol version though. I read and got told mixed reviews of the aerosol version so I looked at alternates.

I then found a stone effect paint by Rust-Oleum, but with this pandemic getting it shipped was tricky. All local stores either didnt have it in stock, or their delivery/click and collect services were unavailable. A company called Plasti-kote do a similar product in various colours so I was on the hunt for that. I managed to find the only can in the area, although it wasnt my first choice in colour, I was too eager to give it a go.

49788322886_22c26e1cf2.jpg


With the pipes removed and prepped it was time to see what it was like. The paint doesnt really give a colour, its more of the coloured texture that sits on the surface. The front Intercooler pipes were originally black, so these came out slightly darker. Compared to the throttle body J pipe and turbo inlet elbow. To be honest, unless you knew you probably wouldn't notice.

Here are some before and after photos

49788254046_1d1648cce7.jpg


49788254036_3d82466cdb.jpg


49788253976_86177b8025.jpg


49788253996_23debdb528.jpg


Accessable areas degreased and cleaned
Intercooler pipes and Turbo inlet elbow painted
Hoses replaced with red silicone inc new stainless clamps
TurboZentrum Silicone Turbo hose fitted
Turbo head shield repainted
Boost controller mounted correctly, new hoses fitted
Boost controller wiring tidied up along the bulk head
Passenger side turret wiring tidied
Amp power cable wrapped in loom tape to hide the yellow
Ground cable kit tided up and re-routed
Carbon Canister, purge valve, hardlines and pipes removed
Throttle cable adjusted (had quite alot of slack)

49787713033_557220f42c_k.jpg


49788571917_dce2a4735b_k.jpg


49788572002_cd992788ca_k.jpg


49788572047_d5d388d4f9_h.jpg


49787712913_6382d3f218_k.jpg


49787712853_7cb8457cef_k.jpg


Its by far the cleanest or tidiest engine bays but its a start
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Found some newly built industrial units around the corner from the fiancée's work. Would have been rude not to take some photos while I was there :p

49842262867_7404f1f3b2_c.jpg


49841962676_afc1d089c0_c.jpg


49841961451_1d67a74b0c_c.jpg


49841422513_49fd3dfc97_c.jpg


49842263432_37a9366812_c.jpg


49842263212_c37f76da65_c.jpg


49841421598_97fa6cfc9f_c.jpg


49841961336_3bca0d2a5c_c.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
I've always loved the look of the BNR34 V Spec II rear diffuser, unfortunately they're expensive second hand and even carbon fibre copies are £1k. So i decided to attempt to make my own using inspiration from it. I'm by no means a fabricator so please be easy on me lol

The first decision was material, I wanted the brackets to be strong, the main diffuser strong enough to be sturdy but doesn't weigh a tonne. I decided to use 2mm thick angle iron for the side and rear brackets and 1.5mm steel box section for the front bracket.

50002472716_28d735d1e3_c.jpg


Looking at mounting points and there is a part of the chassis that sits lower than the bumper, this should be ideal

50002730277_336b0c7c4f_c.jpg


The diffuser and fins were going to be made out of 0.9mm sheet steel. I did think Aluminium as its easy to work with but its too soft IMO. I started off with a card board template, unfortunately the exhaust sits too low at an angle for the whole diffuser 'body' to be a single piece. I tried cutting a hole to try and clear it but it left minimal material at the bottom and it would eventually snap.

So i went with a 2 piece design instead

50002730247_cf27e4d24a_c.jpg


50001953838_146b41c68c_c.jpg


I started off with the passenger side as it was smaller and easier to mount. A slot was cut for the exhaust hanger with enough room for any movement. The rear is braced with a piece of 2mm flat bar which uses a bolt in the wheel arch to the right side of the shock absorber.

50002472726_03b10fcafc_c.jpg


The box section bolts through the boot floor, this helped angle the diffuser down rather than having it flat. This was the first prototype for the box section, later on I made it longer so it covered the width.

50002730397_232ed69a1e_c.jpg


You may remember me making a rear tow hook awhile back. I decided to incorporate it into the design by cutting a slot, again enough roof to not catch it when fitting/removing.

50001953823_70c51ee58a_c.jpg


I seeked help from some friends as I don't have the skills/equipment to weld or fold sheet metal perfectly.

50001953633_729e918685_c.jpg


With the fins folded I could mock the ends up. These would be bolted on and use the same mounting points as the diffuser itself

50001953678_d2fd4310a8_c.jpg


50001953613_35a76ee479_c.jpg


The rear bracket was made and mocked up at the same time. I also marked the holes for the centre fins ready for drilling. At this point I decided to give the front of the diffuser a minor bend upwards rather than leaving it straight.

50001953593_e56befcb30_c.jpg


With everything fitted for one final time,checking clearances and everything was solid and not rattling/vibrating it was time to drop it off for powder coating. Originally I thought about having it done in black, but with the lower black trim just above it, I feared it may get lost and wouldnt be seen. Only other option was silver, the powder coater only had a satin silver so I bit the bullet and went with that.

I ordered stainless nuts, bolts, washers and rivets for the final fit

50001953538_39755a1d1d_c.jpg


50002730067_de72651aea_c.jpg


50001953513_880e5e6eba_c.jpg


50002472451_bfb45a0808_c.jpg


50002730127_9cb9035363_c.jpg


50002730037_c45ee332d5_c.jpg


I've made flat under bumper splitters, canards and other little bits and pieces in the past but this was certainly my biggest challenge. I think its turned out very well :)
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
On Monday 27th July we welcomed our daughter Mia Rose into the world. Mum did an absolutely amazing job and active labour was just over 3hrs long. She's yet to go out in the R34 yet as we still need to sort out the car seat (isofix in the daily Mazda 6 is a god send)

50172110628_43dee08044_c.jpg


After damaging the Work Emotions back in February, they were refurbished during the Covid-19 lockdown. From the factory in Japan the inside of the spokes are darker with a very bright outer face. The company were able to replicate it,but unfortunately the outer face is slightly darker. I had all 4 wheels done so they all match and they look just as good as before!

The car is filthy and is in a need of a deep clean but couldnt resist getting some photos

50172908387_be4ebb4044_c.jpg


50172908377_fc8706816e_c.jpg


50172908362_fae995caf0_c.jpg


50172908397_cc6e07faf5_c.jpg
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
I can't believe the last update was in July!

In September I was lucky enough to attend the 2nd show of the year dodging the national lock downs, this was Modified Live Snetterton. Would have been rude not to as the circuit is only a 20min drive away.

50826320416_d8525d3ef5_c.jpg


50826415467_d8c59f837d_c.jpg


On the drive home the car threw up the TCS,SLIP and EML lights on with no change in the drive of the car. I took it to work the following week and I experienced a very bad misfire on the way in.

Not having access to Nissan Consult I did the paperclip trick and code 21 appeared, which points at the coil packs.

I removed the coil packs to check the resistance to find 4 out of 6 had no resistance. I'm guessing they're fine on initial start up but break down when they get hot (driving for 10mins after start up the misfire reappears)

I also noticed 3 out of 6 cylinders had oil down the spark plug chambers and on top where the coil pack sits. So I started to strip it down while I wait for a replacement gasket and half moons to arrive from Conceptua Tuning.

50826316101_e08da27b66_c.jpg


This was the first time working on the engine especially an RB, and wow what a ball ache this was haha

With the gaskets and spark plugs changed it was a waiting game for the OEM coil packs to arrive from Auto Extreme

50825569458_21a60cebf1_c.jpg


Refitting is very straight forward so it didn't take too long to put everything back together

With the car reassembled it was time for a test drive. What better way than a 100 mile trip around the Norfolk coast. The car didnt play up at all and ran like a dream. An added bonus Mia had slept for the whole time, winner!

50826316071_b651813c3a_c.jpg


I'm looking forward to the salt free roads so I can enjoy this again
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
I've been wanting to try a new photo look/technique for awhile but hadn't had the spare time.

The car had been neglected since the end of summer last year and I can't remember the last time it was washed. Unfortunately with winter and moving house it wasn't at the top of my priority list (plus living in a flat didn't help)

With the car washed, now was the time to go out and take photos. I'll let them do the talking

51107171749_6f63b6f83a_c.jpg


51106851627_631e7c4176_c.jpg


51107171734_f48726e84b_c.jpg


51107431156_4d6abe0c8f_c.jpg


51108204525_034a9d99a2_c.jpg


51106851667_6bfccb6979_c.jpg


51108204575_c228440c2c_c.jpg


51107431246_ab0cc450d3_c.jpg


A big thank you to David Cox aka Shooting Dave for videos, it certainly helped. Just need more practice now
 
OP
OP
hoodedreeper

hoodedreeper

Ex. Club Member
Its been a year since I last posted anything constructive (new coilpacks, rocker cover gasket etc)

The R34 had taken abit of a back burner due to the Micra K11 and Colt CZT but it's time to give it some well deserved attention

Back in 2020 when the UK went into its Covid lockdown, I repainted the intercooler pipes in a stone effect paint. While re-assembling I noticed the paint had started to come off, thinking it'd be fine. Fast forward a year or so and the paint didn't last as long as I had hoped.

With the car currently off the road for the winter, it was a good opportunity to sort this.

I went with a VHT wrinkle black paint, something subtle but not plain and boring. The wrinkle texture wasn't as pronounced as I remembered but its a big improvement from before

Heres a before photo

51852301511_83b5d53202_c.jpg


(Apologies for the phone photos)

51852954690_65a8929079_c.jpg


51852625049_0d02a5334e_c.jpg


51852301481_7d79e6bc34_c.jpg


51852954630_ed131d6741_c.jpg


51852412308_25c397d922_c.jpg


Sorry its nothing exciting. Next up is a service and a good clean ready for spring to arrive.

The turrets are now showing signs of corrosion so I need to start saving for the work to be done. I knew it was coming and we all know its nevitable. I'll probably buy the replacement panels from SR Autobodies and save for the labour costs
 
Top