Search results

Hi everyone. I Need a code for this radio after battery disconnect on a new k12 2006 im borrowing for a while. The radio is a Blaupunkt SN: BP538469506350 There was a label taped on behind too; 28185 BC41A ZH-D912 Photos attached. Any help greatly appreciated. I need some vibes to drive along...

Hi. Need a code for this radio after battery disconnect on a new k12 2006. Blaupunkt BP538469506350 There was a label taped on behind too; 28185 BC41A ZH-D912 Photos attached. Any help greatly appreciated. Thank you.

I've Swapped the heater control dials for LEDs on my K11. The original bulbs were both blown. It was easy in concept but really hard to get my fingers in to push the leds in to their holders as heater cable was very short coming through dash and stopped the controls twisting about so had to...

I bought 50cm of 5050 SMD LED strip in orange for backlighting my car instrument gauges. the 5050 LEDs are very bright which is good, but Id recommend getting 2835 type as smaller and not as bright. Because 5050 LEDS were so bright I made a defuser out of a 2L milk carton as too bright for...

My speedo is face-lift digital so only one connector. The bulbs just twist out with the holder. I've got spare Red leds, T5 / 286 replacements if you need some as in photo. Also yellow, blue,pink,white, Green. PM for details.

That looks like an LED. These will fit, but get a colour towards orange part of spectrum or you won't see the orange needles as shown with blue and green LEDs I just bought.

I replaced the T5 bulbs with these LEDs. They work, but be careful which colour LEDs you choose as needles are orange and green or blue LEDs don't light the needles up.

Straight swap. Just 1 large black connector on the rear.

The original bulbs are T5 / 286 1.2W bulbs. Ive just Swapped to LEDs. Only the small type shown fit in a k11 cluster, I've tried a few. There's one T10 bulb for battery indicator too.

Thanks pollyp for the info above. Ive just done my belts on a 2002 face-lift k11, 1.0L with power steering, no air con. CG10DE engine. The water/PAS belt that was on was a Nissan part no. 11950-1F700 which is Gates' 6PK725, but i struggled for hours trying to get it on, wish id bought a 728mm...

I've just bought a new thermostat. (1.0l k11). Just noticed it's 88⁰ rated where Haynes manual says 82⁰. Will it make any difference?

I bought a new resistor card 2 years ago, about £6 on ebay or ali-express. But its blown again so after repairing it 2 weeks ago its gone again. When I bought the card they sent me the wrong one, its a common type used on many cars, see photos. So I got the plastic connector off the pins with a...

My engine temp gauge is suddenly showing lower than usual temp since the cold spell of weather last week. (See photo). Usually the dial is just below horizontal when heated up (blue line), but last week it didn't get above where I photographed it. Will see if it's better tomorrow as weather is a...

I found a key programmer (clone) with good prices in Nottingham area. They do a post service if you want to risk sending key in the post. www.keymoon.uk https://www.keymoon.uk/nissan-micra-key-nsn11t.html

Same here, need to get a spare ignition key programmed too, blue immo chip

To repair the rubber i cut 2x small plastic crescent shapes out of a milk carton and put them inside the fob over the 2 micro switches. The switches tend to break off at the solder joint but easy to attach a new one. When putting the fob back together wrap insulation tape around the outside...

FIXED: I have fixed this issue. I cut a hole in the perpendicular plastic ridge on the back of the trim to get a cable tie through. Then I put the cable tie around the hinge and pulled it tight. If i need to get it off ever i can get a blade in to cut the cable tie. Hope this helps someone with...

These resistor cards are not fit for purpose. Too much current goes through the thin tracks and they burn out. Im going to fix using 3 x 2 ohm 5Watt resistors. Im guessing 2ohm from all the info ive found about this circuit seems to be right.

FIXED: (SEE BELOW) Has anyone got a better way to fasten the seat hinge trim on so that it doesnt keep falling off? The plastic clips used by nissan dont hold the trim on very well. I was thinking of drilling a small hole in the trim and using a small screw grommet in the hole in the hinge and...

Hi Paul, Thats exactly what i did. Outside and inside.so far its not leaking, but ive got a feeling the silicone i used isnt very good. But for now its stopped the leak.