Search results

  1. Y

    Ball joint replacements

    Ok on my K11 the balljoint is pressed in but the surrounding metal is also folded over. It CANNOT be replaced on my particular example. :(
  2. Y

    Ball joint replacements

    Yeh haven't found any decent suppliers for the wishbones here in Aus. Only Nissan who want my left testicle for them (read $250AUD for wishbone). My existing bushings are actually OK! Can't believe it but they're not cracking or anything. Perfect condition and I can barely manipulate them...
  3. Y

    Ball joint replacements

    Hi fellas long time no see! I'm in the middle of pressing out my front bearings (turns out that you really shouldn't drive through water that is over the centre of the wheels... lol) and upon pulling it all apart I've noticed the FLH balljoint is a bit slack. Now I've been told by everyone...
  4. Y

    Strange noise

    Might not have been what you wanted to say but its what you said. its = it is
  5. Y

    Strange noise

    If his vehicle is Right hand drive this won't be the case as the expansion tank is on the left hand (passenger) side of the k11 engine bay?
  6. Y

    Gearbox Out

    Dropping the gearbox in a K11 is actually really easy. its not really a tight operation at all. You just need a good socket set, some jack stands, good jack and some common sense. Oh and some big pry/lever bars to wiggle the gearbox and engine apart. ALso a pipe extension and breaker bar to undo...
  7. Y

    im sorry but.......

    Oy! You stole my line! lol Opels stink. Worst cars ever.
  8. Y

    help on a zoidberg clip!

    I'll have it. yombet at iinet.net.au :) Thanks
  9. Y

    ***thinking of geting rid of my car***

    Yeh saving money by going to an older car isnt always the brightest idea. Keep the K12 unless it starts to play up and prove unreliable.. :)
  10. Y

    When it floods - best way of starting up again

    I fixed this issue. I had leaking injectors. Replaced them with some second hand injectors which werent leaking and yay. No more problems.
  11. Y

    185/50/R14 or 195/45/R14

    Going with a wider tyre CAN make the handling worse. If the sidewall is billowing out because the rim is not wide enough for the tread its kind of like driving on underinflated tyres. However the tread width differences between the 185 and 195 will be ###### all - it'll be more dependant on...
  12. Y

    Help!!

    The haynes guide is exactly that, a guide. As you're in there you may notice some easier ways to do things. Yes you'll have to drop the oil from the gearbox and remove the driveshafts from the car completely (undo hub nuts). Not overly hard at all. About the hardest part will be levering the...
  13. Y

    Suspension Bolt Torque Settings

    Haynes says 177nm for a k11 and considering it uses the same suspension design as what most fwd vehicle use (macpherson strut + single lower wishbone) it should be fine for the k12. If your torque wrench doesnt go that far just do them up to what you feel is over 100nm. Also if you have non...
  14. Y

    Help!!

    Yes the LUK clutch will be fine - quality is always consistant with the LUK's. As for removing the gearbox and replacing the clutch - easy if you have a brain and don't follow the haynes (it is evil :P). The gearbox itself is pretty darn lightweight, shouldn't pose a problem to any non-geeky...
  15. Y

    Leaking Gearbox??

    Nah not really. Regardless of mileage and use seals will still deteriorate. Infact a lack of use can cause them to deteriorate faster than usual.
  16. Y

    Theres a rat in my exhaust pipe!!

    Yeh be careful touching that stuff if its fibreglass. Your hands will be itchy for a very long time. lol
  17. Y

    oil leak

    Well its usually a biarch to remove the bolt so now would be an ideal time to get a lighter weight 1L crank pulley. :p
  18. Y

    oil leak

    To add to what Fordy posted you will have to inspect the crank shaft as well. Often the seal will act as a lathe on the sahft and it'll dig a nice hole around it. I'm not sure what you guys call them but to prevent it from leaking again (even with a new seal) you might need to buy a "speedi...
  19. Y

    Quick question - Super S

    i got pas standard on my super s. All our 96 update and newer k11 super s had power steering, aircon, abs and 4 wheel discs standard. hehe Wish they didnt have the pas standard though. Its not needed and it just adds weight and saps valueable power.
  20. Y

    major annoying starting problem

    I solved all my starting issues. 3 out of 4 of my injectors were leaking. Leaking quite badly too. Mass flooding issues under certain circumstances. Fixed it by replacing the leaking injectors!
Top