Search results

  1. frank

    Engine Conversion K11 ➔ PAO

    i ran the smaller k10 derived prefacelift k11 1.0 g/box without any problems, cga3+t
  2. frank

    Micra 1.5 dci white/ bluish smoke-Suspecting Turbo??

    if the shaft is ok it wont be the turbo then sam, and if the coolant has,nt gone down it wont be the head gasket (the expansion bottle will go up and down, when hot and cold)
  3. frank

    Micra 1.5 dci white/ bluish smoke-Suspecting Turbo??

    all my turbo,s were from scrapyards £50 ish, i buy loads of pistons and cylinders from china and have occasional piston ring problems, never bought a chinese turbo tho
  4. frank

    Micra 1.5 dci white/ bluish smoke-Suspecting Turbo??

    best to check the turbo for play first sam, this one of mine was shagged but still did,nt smoke
  5. frank

    Idle issues - please help

    all of them i guess, in order tor the long term and short term fuel trims to work
  6. frank

    The £80 Micra

    should,ve turbo,d the 1.0 imo :) same hp as a moderate n/a 1.4 build, and dirt cheap if you cut corners and you build not bought it
  7. frank

    The £80 Micra

    typical 1.3/1.4 oil burning and crank journal wear, most of mine drank oil and had low oil pressure. white smoke is probably just the weather conditions ? and i could,nt live with engine vibration personally, i left the stock side mounts that carry the weight of the engine and then filled the...
  8. frank

    Micra K11 running like dirt (p0132, p0138 and p0443)

    not sure a k11 has a purge valve circuit, spurious codes maybe ? best to monitor the o2 sensor voltages on torque app or whatever, to confirm those codes are legit
  9. frank

    Idle issues - please help

    thats the point of the self learn ecu,s on the coilpack engines, as the sensors go out of sync with age, the ecu compensates to a degree hence the need to calibrate a new sensor when its fitted (pedal dance or reboot or whatever)
  10. frank

    The £80 Micra

    £4 ish , a4 size on ebay eh
  11. frank

    The £80 Micra

    carbon fibre cloth and resin :)
  12. frank

    Front Crossmember Replacement "How-To" link dead

    the guides used to be for paid members, is it this one ? https://www.micra.org.uk/threads/how-to-replace-your-front-crossmember.39325/
  13. frank

    Front Crossmember Replacement "How-To" link dead

    probably a members only link alex
  14. frank

    P1706 code engine light on +no reverse light still.... after changing the switch and light bulb

    usually you check for a live at the switch, but yours is probably canbus tho, which is more complex and wont show a voltage until you apply a load
  15. frank

    Hardrace Engine Mounts

    preface 1.0 have some different mounts
  16. frank

    Gearbox oil change

    just follow the speedo cable down, 10mm bolt and a paper gasket that had probably welded itself to the casing
  17. frank

    Gearbox oil change

    you have to remove the speedo drive, and fill it to the plastic cog
  18. frank

    Spigot rings

    the old hubcentric/lugcentric debate, how much support does a plastic spigot ring give ?
  19. frank

    Help to get NON NATS ecu to run a NATS car please.

    on the pre 2000 k11,s ed used to switch about 4 pinouts inside the ecu, if k12,s are the same then that would be the easiest route nissan switched the wires to stop anyone swapping a prenats ecu in to steal the car
Top