• Please only use these forums for blogs, they are not a discussion forum

My K14

Here’s my K14 micra ,
It’s a SV premium + , 0.9ig-t , and it has the orange exterior trim pack and 17” alloys with orange insert. So far it’s been nice having a new car drives nice just about enough power to get about at a reasonable pace. Iv a few mods planned a dump valve a set of lowering springs and a set of wind deflectors for now soon as payday comes I’ll order some of it car needs a good valet and polish first though.
Today I removed the awful dealer plate holders but the animals used self tappers for the rear and the original mounts are raised so I couldn’t Velcro that plate on so there’s no screws I’m going to have to sort something better out

476c0766d4f8d69c1d49778faa9739a4.jpg
fb4bcb841c25c0006092a8d3f3fe03fc.jpg
d8eba522075ba10dc4686f2c6a665544.jpg
c841b15d0b7682970e15870ba0b4ed73.jpg
d3bdc3f3fd155a1d83db7daf7577fc7c.jpg
c74084fbb0f2971a2d053b77ee79bfc3.jpg
b32b68e23f1305429a0c53f7796f9c13.jpg
224aaaa07fbbcb1e5d17b3e461d6cd2d.jpg
b25bb43e8d13880fefa2ff57ce1f0346.jpg



Sent from my iPhone using Tapatalk
 
Any updates on the forge kit?

debating moding my k14 with a cone intake and lowering but, can’t fine any places that sell full coil over kits except in Germany and from the uk
 
Not yet, it hasnt arrived, the courior service has lost it for about a week They assure me it will be with me today or tomorroww . The H&R springs have arrived and will be fitted saturday this is my family car so coilovers are out of the question the pulsars getting the coilovers.
 
I've order a Dump valve kit should be with me in the next week or so if you manage to fit it before me please post some pictures of installing it as i have no clue what in doing lol

please post a picture of the car on springs as I'm debating buying some to lower 35 mm
 
2b888fccc1f4e804384a14b6bc5b159c.jpg


6b0a447cfb42127b2d1beed1c80dfa28.jpg
.

Very easy install, remove old recirculating valve and pipe to intake fit forge valve and block intake with the supplied hose , Iv a box of spares too vac line a 25mm hose blank and a T piece


Sent from my iPhone using Tapatalk
 
Just had delivery today sadly they shipped the wrong valve and no parts so they’ve sent it again next day delivery so should be with me tomorrow ?? How does it sound?
 
Not much happening lately got some buddy club P1s for it , fitment looks like it’s going to be good 7x17 et42 I think gives about 14mm more poke all round , sent them off for fresh powdercoat, got some yellow LED front fog bulbs and also got some LED numberplate lights.




fb11b4229e2676215c53f0deaeefb8c5.jpg
35de316795a70c97a29d067deb7367b1.jpg
e521176970496733cb19415182c0b481.jpg



Sent from my iPhone using Tapatalk
 
Been planning on bits a pieces and fitted a forge dump valve unfortunately bd weather conditions on the weekend
 

Attachments

  • 3F10D111-98C6-4B73-B9D6-E5CD0ED5496B.jpeg
    3F10D111-98C6-4B73-B9D6-E5CD0ED5496B.jpeg
    1.9 MB · Views: 337
Finally have the car back and I’ve order a new performance chip should increase bhp by 15-20% and increase acceleration
 

Attachments

  • B96141CC-CAAF-4E25-86C1-B45F3368B38C.png
    B96141CC-CAAF-4E25-86C1-B45F3368B38C.png
    1 MB · Views: 337

Low Rider

Poindexter
Founding Member
Moderator
Club Member
Finally have the car back and I’ve order a new performance chip should increase bhp by 15-20% and increase acceleration

Most tuning companies here advertise 0.9TCE remaps at around 110bhp / 200Nm, which is a fairly decent improvement.
 
Anyone got any clue on how to remove the interior trim around the around the radio and air vents. and any idea on how to remove the steering wheel to take of the silver piece on the lower half (all are being wrapped but have no clue on removing them).


1554300297701.png
 
I seem to be a bit late to the party, but I've got myself a micra now too and wanted to know what sort of mods would be good for the car. I've got no experience with modding cars so I'll take all the help I can get.
 
Top