Corsa piston build with throttle bodies

Took a couple of coils of the front, felt a bit 'tighter' to drive

Might have to beef up the rear mount maybe?

51f0a9bec169834dd832c3125d8ba3dc.jpg


73c0bd207ad515753b1d9eabc6e1569c.jpg



Got a map sensor of my mate to play with for free...........along with his old redline developments ecu for free..........only catch is he thinks the injector coils have fried on it, surely must be repairable?


Sent from my iPhone using Tapatalk
 
Got the ecu.....looks ok to me, I'm hoping it was down to the previous wiring attempt on the plugs that was giving my friend the issues, he seemed to think the ignition drivers had burnt out

Either way, il use this to make up the loom and stuff, it's exactly the same as my old ecu that was on the k10 (now mini)

If it don't work, at least it'll just be a case of replace the ecu

c1549e99d837326032bd17dd3b2c153e.jpg


5034c399e2f93ce834cda7f0a3a560e6.jpg



Sent from my iPhone using Tapatalk
 
Started the loom for the ecu

c267af98bdc34398ecf01538be8691bf.jpg


Bought a 165/45/15 tyre to see what it'll look like on these wheels.......think it'll be ok with more lows

f55353c34d8cbc056ece1060a4a135bf.jpg


169bdb742c604e99fa406198f8d01419.jpg



Sent from my iPhone using Tapatalk
 
Got the cams back from autosprint.....

ce8681c9a9cae8955d64dcae01098437.jpg


9941b6975376be529599b04c3ef34fa4.jpg


And a pack of shims of frank


Now gotta fit them lol

Gunna take note of the shims height, and guess il move/grind them about till I get the right clearances


...........what should I be getting and where should I be taking measurements from?


Sent from my iPhone using Tapatalk
 
Also......cam bloke said to put the shims under the bucket......there's a raised part under there, do I have to cut/grind a bit outa the new shims so they sit flat inside

1c61bea501213ab57106dc1a1e772a6d.jpg



Sent from my iPhone using Tapatalk
 
you have to bevel/shamfer the top edge around the lower shim neil, there is one in the set iirc
and a 10" thou feeler when the lobe is at 12 o,clock
 
Il have a look.

Don't have to worry about the centre bit then?

Also......I've got what clearances to look for.........but no idea of where to check



Sent from my iPhone using Tapatalk
 
when the lobe is off the bucket there should be a gap neil, if there is no gap the valve will be held open (no compression)
 
and juggle the shims around to get a 10" thou gap, and if the gap is too tight grind a tad off the middle of the shim (where that pip you asked about makes contact)
 
Cool, cheers


Looks Like this will take a while!!

I don't need the sprocket/chain on do I?


Sent from my iPhone using Tapatalk
 
Right, I've put all the bottom shims in and this is what I've got with the feeler gauge

Top numbers, inlet cam

33f25c73f4a7ded3fc7948cff489e342.jpg






Sent from my iPhone using Tapatalk
 
df0b4bb57e1c6da2213c530001bb906f.jpg



Just swapped some about.

So would I be able to use it like this?


Sent from my iPhone using Tapatalk
 
Haha, I guess so mate......same as before?


Is there any bedding in procedure I need to do......like keeping a certain rpm for a few miniutes


Sent from my iPhone using Tapatalk
 
Because I'm a child and impatient, I started the engine as it is

I let it rev in its own for 10-15 mins to warm it up

Is a bit tappy, so will definitely have to swap some shims about.

Went for a quick drive......above what I think is 2-3k, it goes mental lol

What I have noticed though is it doesn't get as hot as quickly as it did......with the old cam, even after a short drive, the rocker cover would be roasting hot.....now after the same length drive it's cooler,

Not sure what that means , but must be better for the engine


Just ordered trigger wheel and does edis Kit, so can start wiring up new ecu

Really wanna get these itbs on


Sent from my iPhone using Tapatalk
 
if they are the 270deg 10mm lift ones they are quite an aggressive profile neil (jerking the valves open and shut) which is why i set mine at about 10" thou (.25mm) and they have been known to spit shims out (i ended up running with both shims under the bucket to avoid it)
geoff,s other profile is the old mini 544, which looks less aggressive but more laggy

P9191245.JPG
 
These are 274 degrees and 0.355 lift......what he recommended with all the other things I've done and going to put on

Il have to whip out the cams again and see what these top shims are.....then figure out the correct sizes and get back to you mate.......maybe next week if I can find the time

Got keys to new workshop so will be busy moving that about for a while now


Sent from my iPhone using Tapatalk
 
Got some bits through

Trigger wheel, crank sensor .....and ford coil pack

The ecu I've got on the mini is the same as this.......I'm using the micra coil packs driven by the ecu........surely I can do the same with this thing (I don't have the edis module)

209c18390950d22726b73885f51bd670.jpg




Oh yeah, still haven't learnt from past goes at this.......one colour loom

09f59fff5c0d2007607fb67f67aa8b7d.jpg



Sent from my iPhone using Tapatalk
 
fire the micra coilpacks semi sequential neil ?

I don't have any micra coil packs mate (on the mini)

......and that cam plate I got from you has gone walkabouts


Apparently I can run the ford coil pack straight from the ecu


Sent from my iPhone using Tapatalk
 
Hmm, i may have those of you at some point then mate

Gunna set this ecu up how I know for know (batch and wasted spark)

.......I still don't know whether this ecu works or not

(Was given to me for free)


Sent from my iPhone using Tapatalk
 
Anyone help me by telling me what wire is what in the lambda sensor


Sent from my iPhone using Tapatalk
 
Just trying to figure out how to wire it into my ecu

How does the heater wires go?


Sent from my iPhone using Tapatalk
 
Is it.......


+ from ignition to heater
Signal to ecu
- chassis to heater


Sent from my iPhone using Tapatalk
 
paul says that the 2 black wires are heater + and earth neil, but i was under the understanding that they are both heater + wires and earthed through the body ?
 
Spose I should get 12v on both wires then?

(Not by the car to try)


Sent from my iPhone using Tapatalk
 
Had a spare afternoon so I've roughly wired up the plugs

I've kept all the old micra stuff in its place, just disconnected for this test


c99586e11dbd58363b9226bece533280.jpg


a865ca0143dc73975f355bcdc36ab53b.jpg



This ecu I got was for free.....coz he thought the injector drivers were shot.........I think he's right I've put 12v leds in the plugs .....when I crank, the laptop says it's sending the pulse.....but nothing happens at the plugs......dam........need to buy another ecu





Sent from my iPhone using Tapatalk
 
Got it going !

Don't think it was running on all 4

Need to sort fuel map....... or buy a wide band and key auto tune sort it out




Sent from my iPhone using Tapatalk
 
It's the Ignition driver that's dead on this ecu
So......

Borrowed the ecu from the mini.....it's the same one

So just plugs and plays.

Loaded up a generic n/a map

And...........






It works, on the itbs, running it on alpha-N at the moment,

It's idles like ****, don't think the cam helps

Took it for a drive, only works if you floor it.....shifts though!

Few problems to sort, the trigger wheel is cutting into the chassis leg
Need to remove the dizzy, but had to keep it plugged in for now until I find the fuel pump wire (think you need rotation from dizzy to make pump stay on?)

Need to strip the micra loom way back too, only things I've got plugged in from micra loom are dizzy plug, wiper motor, and heater for o2 sensor, the rest is unplugged.......it's a mess

d511c74c7565489510cff0a097bb3660.jpg


dbcb7acde49bd4e78219c46bf3b300f9.jpg


125e9acf3b146c806eed8d61825bb7a6.jpg







Sent from my iPhone using Tapatalk
 
Back
Top