Recent content by Vic222

  1. Vic222

    Question about blocks

    Thanks frank. Even if it isn't semi closed deck still a good spare engine with low milage.
  2. Vic222

    Question about blocks

    Is it true that the automatic micra engines come with a closed deck block? I have low milage automatic CGA3 in the shed as spare and can't be bothered taking it apart to check. I know the manual ones are open deck. That is a ****ed manual CGA3DE block which I have lying around. If indeed the...
  3. Vic222

    Ram air induction kit

    You are better getting the filter nearer to front of the car to get cold air especially on an na setup.
  4. Vic222

    Question about cylinder heads

    Both heads are coil pack. So it's good to know they are interchangeable if you change the cams over.
  5. Vic222

    Question about cylinder heads

    Am I right to assume that the main difference between a cga3de and cg10de cylinder heads is the cams. I am looking to fix a spare cga head with bent valves I have a spare cg10de head for donor valves. Looking at a supply catalogue it gives the same part number for the cg10de cg13de cga3de inlet...
  6. Vic222

    air restriction over 5000rpm

    I believe the problem could be the valve timing being 1 tooth out. Inlet valve closing too early I have been told the car will still run but loose power at top end. In isn't maf frank after talking to the garage, they are using the map and intake temperature to work out the air volume. Will have...
  7. Vic222

    air restriction over 5000rpm

    Just the stock cga3 sensors plus map and intake temp sensor (which was installed prior to mapping). I am confused by it aswell. The rocker cover gasket was leaking so he is going to replace it. I have stanis old turbo kit with a new turbo and air filter so the setup is proven to work in terms of...
  8. Vic222

    air restriction over 5000rpm

    What the guy said over the phone "engine is loosing power at 5000rpm and beginning to run rich not getting enough air". Removed the air filter etc still the same. The car was mapped before on k6 with rally cams and had a soft cut limit at 7000rpm was running great i have removed the rally cams...
  9. Vic222

    air restriction over 5000rpm

    My car is currently at a local tuning garage getting mapped with a td04l turbo on a CGA3DE run by emerald k6 ecu. A map sensor was fitted car is making great power up to 5000rpm then starts to run rich not getting enough air the turbo is set 7psi and does make boost. I am guessing there is...
  10. Vic222

    K11 Uprated Clutch Options?

    http://www.rallynuts.com/nissan-micra-k11-transmission/helix-76-6035-cerametallic-paddle-clutch-plate.html I got this one on with the competition cover and new release bearing. The good thing is that clutch can be run with a stock plate and release bearing I think it is 180mm if I remember...
  11. Vic222

    Civic half size radiator

    Cheers for that
  12. Vic222

    Civic half size radiator

    Just wondering has anyone fitted a half size civic radiator on a k11? They look like they will fit I know a lot of people put them in Toyota glanzas.
  13. Vic222

    Stand Alone ECUs

    The problem is I am up in Scotland. There isnt many garages up here with experience in micra ecus. I think standalone is my best option.
  14. Vic222

    Stand Alone ECUs

    Does anyone have experience running a Haltech Sprint 500 on a CGA3DE engine. I know most people go for omex but my local tuner doesnt have experience with them. I have been told it should work no bother. The car will be getting turboed after the ecu is up and running.
  15. Vic222

    Question about ECUs

    I have a chance to get a nistuned ecu for my turbo build. My question is whether it is compatible direct plug and play on 2000 1.0 k11 coilpack car which has been engined swapped to a cga3de 1.4 The car runs fine with the 1.0 ecu. The 1.4 car which I got the engine from had a bosch ecu so I...
Top