• Please only use these forums for blogs, they are not a discussion forum

PollyMobiles Rebuild

with the rear 1/4 painted, I can now move the car out the garage for more space to sand & primer all 3 remaining doors

IMG_20210628_184622.jpg

IMG_20210628_184551.jpg
IMG_20210628_201247.jpg
IMG_20210628_201311.jpg
IMG_20210628_221215.jpg
IMG_20210628_221323.jpg
IMG_20210628_221336.jpg
IMG_20210628_223814.jpg
 
Great work as ever Paul, I'm just glad I run rally cars where I don't have to worry about the state of the paintwork, as long as its one colour and it keeps the rust a bay thats all that counts. Scratches and marks, are all 'war wounds' of competition! :)
 
Looking great. I've just bought some BR RM coilovers and have to paint my front right wing. What sander are you using? Can't wait to try my new and improved Micra.
ooh, you got any pics of them? arent they with inverted monotubes?

it's just a cheapo £30 screwfix random orbital sander I'm using with 180 grit discs to flatten the bulk of the bodyfiller and then finish it off with 400grit wet sanding
 
Great work as ever Paul, I'm just glad I run rally cars where I don't have to worry about the state of the paintwork, as long as its one colour and it keeps the rust a bay thats all that counts. Scratches and marks, are all 'war wounds' of competition! :)

it would be convenient if I could just paint it flat matte black but I've grown fond of her unique colour ?


a5491adfc14b90637f4ff9f0d35afe30.jpg
 
painting & lacquering the drivers door and the rear passenger door went well :cool:

holding down the rattle can nozzle for ages to paint & lacquer each huge surface really really strains the fingers ??

IMG_20210629_235855.jpg
IMG_20210629_235558.jpg


the rear drivers door had a slight disaster, I sprayed too much on which resulted in an ugly rippling paint run & slight crack & pin holes ?
can't laquer over this obvious eye sore ?

IMG_20210629_214019.jpg
IMG_20210629_214042.jpg
IMG_20210629_214507.jpg


so I wet sanded the area down with 1200 and resprayed it. I think I got away with it ?
gonna lacquer it tomorrow

IMG_20210629_235615.jpg
 
lacquered the rear offside door, fitted the doors & fuel cap into the car and yess! it looks soo much better :love:
damn proud of that after 4 weeks of hard work :cool:

all the same colour & glossy finish, and will likely need a good 2500 grit wet sand to get rid of the fine orange peel

IMG_20210630_211606.jpg
IMG_20210630_212009.jpg


next task is to mask, sand & paint the A pillar / roof matte black

the rest of the car really needs a good wash & buff from all this dust
 
masked off the A pillar & roof edge

IMG_20210701_191429.jpg
IMG_20210701_191443.jpg


sanded & primered

IMG_20210701_201142.jpg


and sprayed matte black :cool:

IMG_20210701_202839.jpg
IMG_20210701_213455.jpg
IMG_20210701_213523.jpg


reassembled all doors & front end

IMG_20210702_222822.jpg


the bonnet was full of half polished orange peel so I wet sanded every little dimple off with 2500 grit

IMG_20210703_152058.jpg


began buffing with G3 compound followed by autoglym super resin

IMG_20210703_162013.jpg


inside the garage I could still see tons of deep scratches left by the 2500 but soon as I look at it outside, the sky hides all the tiny defects ?

IMG_20210703_172443.jpg


hoovered the interior

IMG_20210703_174329.jpg


wiped the engine bay

IMG_20210703_174625.jpg


and of course I had to go take a few evening shots of the new paintwork :love:

IMG_20210703_203758.jpg
IMG_20210703_203955.jpg
 
04-07-2021 Cumbria Auto Show

7am we all gathered at MaccyD in Aycliffe to convoy up to Carlisle by 9am

IMG_20210704_074057.jpg


it was thankfully a warm dry morning to the show, wiped her all clean ??

IMG_20210704_110151.jpg
IMG_20210704_110216.jpg
IMG_20210704_110306.jpg


it was a nice big show with soo many cars to look at

IMG_20210704_110337.jpg
IMG_20210704_110358.jpg


even spotted 2 other K11's ?
this was actually graffiti rattle canned satin black and looks good (something I almost would've done out of anger if I didn't solve that cracking paint issue ?)

IMG_20210704_121218.jpg
IMG_20210704_121325.jpg


occasionally there were a few very dark heavy storm clouds heading over and dumping a huge sudden wall of shower over the whole show for a few minutes, everyone running for cover ?⛈️☔

at 3pm ppl had enough of the poor weather and simply clogged the exits lol

IMG_20210704_153300.jpg


I stayed back abit longer for more car pics ??
driving back home through the monsoon flooded roads was interesting ?

IMG_20210704_161723.jpg
IMG_20210704_161736.jpg
 
A m8 needed a small adapter printed for a TPS cos the original one has broken apart

IMG_20210706_231819.jpg


measured the original adapter

adapter1.jpg


printed

IMG_20210706_225912.jpg


fits like a glove

IMG_20210706_231842.jpg
 
after work I began to wash, mask off and sand the front wing with 2500

IMG_20210708_185433.jpg


some bits I went too deep and briefly sanded the base coat/primer ?
polished it with G3 compound followed by autoglym super resin.
you can see just how glossy, smooth, shiny it is compared to the rough door panels ??
but the shine also highlights all the dents on the panel & bad base coat underneath ?

can't wait to do the other panels another day

IMG_20210708_202049.jpg
IMG_20210708_202127.jpg


with soo many empty rattle cans to bin, I've always wondered what's inside em so I cut em open ?

IMG_20210708_212027.jpg


halfords grey primer uses a single 12mm glass marble,

IMG_20210708_212048.jpg


the clear lacquer uses none,

IMG_20210708_212104.jpg


and the paint shop base coat cans use two marbles

IMG_20210708_212120.jpg
 
drove 6hrs round trip to birmingham to finally meet Stefan Navo, have a gr8 chat, went for a ride in kassandra and he kindly donated a few good spares I was after,
including a good head (my spare head was badly pitted),
nissen auto radiator (mine was previously leaking and the fins are all bent now),
reconditioned 1.3l gearbox,
GTIR MAF,
arch liner (mine's battered & melted),
and extra 5hp stickers he designed ?

IMG_20210710_160705.jpg
IMG_20210710_201024.jpg


head is better condition than my other one, so no need to spend more on skimming

IMG_20210710_212814.jpg
IMG_20210710_212905.jpg
 
a m8 Daniel needed a meth injection kit fitted onto his audi TT.
the most logical place to fit the nozzle is this plastic pipe between the intercooler and TB but removing all the difficult clips & fasteners was a PITA

IMG_20210711_120635.jpg


this was the only flat surface for screwing the BPST nozzle onto and clear the cooling fans

IMG_20210711_123041.jpg
IMG_20210711_133935.jpg


attached the solenoid to the airbox tray

IMG_20210711_164644.jpg


mounted the reservoir & pump in the boot

IMG_20210711_164659.jpg


the hardest part was figuring how to route the pipe & wiring neatly through the car.
there's no easy access gromet holes in the footwell or bulkhead,
routing past the door seals looks ugly and will crush the pipe/wires,
the engine loom goes up inside the scuttle panel & deep into the dash but the wiper arms are seized onto the spindles ?

took a lot longer than expected, as usual, so we'll have to wait another week to buy a wiper puller tool, wire it up & calibrate the pressure sensor ?
 
Got myself a cheap 1/2" impact wrench (Makita DTW285Z copy), 18v battery (came fully charged too) & fast charger (Makita DC18RC copy which amusingly plays the Mozart "Eine Kleine Nachtmusik" tune ?) from ebay for just £65

View attachment 73347View attachment 73348



before using it, I wanted to check the internals and regrease em. removed this pointless plastic shroud ?

View attachment 73349

removed the impact mechanism cover, the spindle and impact hammer is bone dry ?

View attachment 73350View attachment 73351

dismantled the impact mechanism, quite a simple but interesting system. the planetary gears have just the bare minium of grease.

View attachment 73352

straight forward internal layout

View attachment 73353

sealed control board

View attachment 73354

yup thats a tiny brushless motor as advertised. I can see the cooling vent exits but there's barely enough cooling intakes at the front (may mod that someday).

View attachment 73355

the motor has it's own 2 bearings while this bigger bearing in the housing is for supporting the impact mechanism assembly.
kinda odd how the metal outer planetary gear locks to this white plastic housing which then locks to the outer casing (probably to keep the planet gear & bearings concentric?)

View attachment 73356

relubed it all fully with generic grease and CV grease. runs noticeably smoother & quieter :cool:

View attachment 73357

brought a pack of impact sockets for £12

View attachment 73345

imho this is mostly good for whizzing light duty or cracked-loose fasteners on/off quickly or shocking rusty fasteners,
but for high torque such as wheel nuts or suspension bolts, while it could eventually loosen em (be it slowly compared to a real Mikita), I'd still use a breaker bar to crack em loose 1st, whizz it off with the gun, then tighten em with torque wrench.

I brought it just to help speed up some of the boring processes (ie swapping wheels at trackdays) and wasn't meant to replace the breaker bar at such low cost.
proper impact toolsets that can replace the breaker bar costs well over £200 which I can't justify spending.

Well it took me way to long to find this post but I remember you mentioned the tune from the charger and I suspect that its a Makita unit.

Did you know you can change the tune?...

 
took a few reflection photos whilst the suns out and pwhoa that gloss ? :cool:

IMG_20210719_173115.jpg
IMG_20210719_172738.jpg
IMG_20210719_172641.jpg
IMG_20210719_172617.jpg
IMG_20210719_172513.jpg
IMG_20210719_172952.jpg
IMG_20210719_173208.jpg


went to fill up and a drop of petrol hit the fresh paint and immediately melted/stained it FFS ???

IMG_20210720_174955.jpg


attempted to polish it out but nope the normal halfords lacquer definately ain't fuel resistant and has a deep chunk melted off it, easily feel the ridge ?

IMG_20210720_212947.jpg


I guess the next possible fix is to sand the area flat, respray it with petrol resistant lacquer, wet sand, polish again and pray ??
 
That blows, is a really impressive finish you've got with rattle cans, so top work hopefully some tougher clear coat will help. Might be a bit of a silly question, but given the number of cans you had to buy, would it not have been similarly priced to buy/rent a compressor and do it that way?

Craig
 
That blows, is a really impressive finish you've got with rattle cans, so top work hopefully some tougher clear coat will help. Might be a bit of a silly question, but given the number of cans you had to buy, would it not have been similarly priced to buy/rent a compressor and do it that way?

Craig

I'm quite happy with the overall result of the rattle cans.
yeah I'm gonna put a few more thicker layers of lacquer under the filler area to hopefully resist the solvent better.

costed a total of £280 to completely respray the whole car and all the empty cans are discarded without taking up any workshop space.

buying or renting all the compressor, air lines, spray gun, primer/base/lacquer, thinners, hardener, strainers & cups etc would probably cost well in excess of bout £400+ total and permenently take up ALL the remaining space of my tiny workshop.

yes it may give a better finish but this ain't a show car and the many drawbacks just doesn't suit my circumstances yet.
 
the door mirrors are looking very beatened & stonechipped over the yrs.

plus the drivers side mounting has an annoying loose shake cos repeatedly folding em in/out has worn the ball&groove mechanism till it can't lock in place solidly (so I'll need a need mirror)

IMG_20210723_214525.jpg


stripped apart all the mechanism

IMG_20210723_220009.jpg


sanded em all smooth

IMG_20210724_145730.jpg


resprayed & lacquered

IMG_20210725_111105.jpg

jeezuz I forgot just how damn frustratingly fiddly it is to reassemble the sprung cable operated mechanism ??

IMG_20210725_135537.jpg


that looks better, matching the rest of the bodywork finish ?

IMG_20210725_141435.jpg
IMG_20210725_141456.jpg
 
the bumpers are the last things to respray.
this original rear bumper is now all battered, scarred & dented. the inside beam is also quite rusty and needs repairing but that's low priority.

IMG_20210725_164807.jpg


test fitting a spare bumper before I paint it. looks much straighter than the old one with less defects

IMG_20210725_170012.jpg


sanded it smooth & primered

IMG_20210726_193820.jpg
IMG_20210726_205145.jpg
 
I'm quite happy with the overall result of the rattle cans.
yeah I'm gonna put a few more thicker layers of lacquer under the filler area to hopefully resist the solvent better.

costed a total of £280 to completely respray the whole car and all the empty cans are discarded without taking up any workshop space.

buying or renting all the compressor, air lines, spray gun, primer/base/lacquer, thinners, hardener, strainers & cups etc would probably cost well in excess of bout £400+ total and permenently take up ALL the remaining space of my tiny workshop.

yes it may give a better finish but this ain't a show car and the many drawbacks just doesn't suit my circumstances yet.

Yeah fair enough, can't complaint too much with a £300 respray! I CBA take my mirrors apart when I sprayed them, didn't get a great finish... I've probably got a spare unit knocking around if you need one?

Wouldn't worry too much about the bumper bar - I replaced mine with a couple of carriage bolts, weights a lot less and makes removal a bit easier too.

Craig
 
Yeah fair enough, can't complaint too much with a £300 respray! I CBA take my mirrors apart when I sprayed them, didn't get a great finish... I've probably got a spare unit knocking around if you need one?

Wouldn't worry too much about the bumper bar - I replaced mine with a couple of carriage bolts, weights a lot less and makes removal a bit easier too.

Craig
does the job ;)

I just brought a spare 1999 facelift drivers door mirror on ebay for £11

IMG_20210728_214238.jpg


although this later design is different, with the bare metal folding mechanism screwed to the all-plastic base plate (whereas on the preface, a metal frame & mechanism is riveted to the plastic outer housings) and it only folds forward whereas the preface can fold forward & backwards

IMG_20210728_214254.jpg
IMG_20210728_214327.jpg


it's a bit more flimsy so I dunno if I'll use it.
oddly after painting & assembling these mirrors, the drivers mirror no longer shakes as much? so I guess there's no need to replace it anymore (y)
 
after sanding the grey primer flat, I sprayed 2 layers of base coat

IMG_20210727_201230.jpg


and then 2 layers of lacquer

IMG_20210727_221521.jpg
IMG_20210727_221603.jpg


after drying overnight & reinstalled it in time for the wednesday car meet.
the raw finish is a bit more satin but it'll soon be sanded & polished the same as the other panels

IMG_20210728_204339.jpg
IMG_20210728_204407.jpg
 
noticed the rear quarter has this annoying trapped bubble under the paint. I tried popping it with a pin but it retains its shape :(
nothing I could do except leave it alone or respray that section in future ?

IMG_20210802_182627.jpg
IMG_20210802_182618.jpg


with just over a week to go till JAE, it's time to finish spraying the front bumper and correct the wonky headlight mounts on the wings

IMG_20210802_204035.jpg


begin sanding and hmm there's sooo many deep dimples from years of stonechip impacts, this is gonna take awhile to do on my busy schedule

IMG_20210802_231258.jpg
 
reinstalled the X-brace for the show

IMG_20210808_135604.jpg


didn't like the rear speaker enclosure I made, which was heavy, bulky & didn't improve the speakers anyway.

I'm gonna buy a powered subwoofer next for the low-freq & let the 6.5" speakers deal with the mid-high end,
so I stripped the enclosure apart.

IMG_20210808_142511.jpg
IMG_20210808_142847.jpg


the wheels are covered in months of orange iron oxide so a few hours of polishing with G3 compound brought back the bright white :cool:

IMG_20210809_184043.jpg
IMG_20210809_184455.jpg


kassandra is now all resprayed & polished, ready for JAE 2021 ?:cool:

IMG_20210809_195459.jpg
IMG_20210809_195536.jpg
 
Vibe Edge EDB10A Powered Subwoofer

Just before JAE I decided that after 15yrs of flat tinny 6.5" speakers it was time to get a dedicated sub for the low freq and won't have to push the smaller speakers towards distortion.

the Sony headunit outputs a peak of 55w x 4 = 220w

I saw halfords was selling this Vibe Edge EDB10a for an affordable £79. has an integrated amp and puts out 250w RMS, 750w peak

IMG_20210811_210650.jpg
IMG_20210811_210732.jpg


it's a class AB amplifier running bout 50% efficiency so it'll need at least a 10awg power cable.
I ordered some 10awg copper cable kit online but didn't turn up in time, so I quickly brought some cheaper halfords CCA cables along the way to JAE so I had something to do at the show and check it all worked :p

IMG_20210811_210758.jpg


after JAE, the 10awg copper OFC cable kit from halfords arrived

IMG_20210815_203001.jpg


CCA vs OFC cables

IMG_20210815_210546.jpg


the bass reflex tube is just a card tub stuck on

IMG_20210815_232745.jpg


here's the amplifier

IMG_20210815_233112.jpg
IMG_20210815_233135.jpg


small patch of wool near the inside port opening

IMG_20210815_233257.jpg


some plastic trim around the speaker

IMG_20210815_234134.jpg


a look at the speaker & internals

IMG_20210815_234301.jpg
IMG_20210815_234331.jpg
IMG_20210815_235311.jpg


temporarily strapped it in place and wired up. ooh it's soo nice to finally have some bass with no distortion ?

IMG_20210816_222713.jpg


the bare speaker is quite exposed so I brought a cheap 12" grill from ebay

IMG_20210821_104549.jpg


the feets have a deep offset so I'll trim them flush

IMG_20210821_104635.jpg


now that's a lot better ?

IMG_20210822_121223.jpg
IMG_20210822_121730.jpg
 
JAE 2021-08-12

Car filled up with E10 for the 1st time, cruised down to Norwich with no issues and did a normal 48mpg.

6pm arrived at JAE, found our MSC stand at the far end of the field near the dodgems and after a 2yr lockdown it's soo nice to finally see james, chloe, alan, sebastian & ben there with the gazebo set up ?

surprisingly I'm the 1st micra to turn up? :unsure:

IMG_20210812_184943.jpg


me, chloe & alan assembled the new BBQ whilst james & sebastian erected the new overhead perimeter lighting which is a brilliant new upgrade. plus an overhead lamp heater inside the gazebo was handy for the colder nights.
Harlen soon arrived in his R33 skyline followed by Faith in her Honda Del Sol ?

IMG_20210812_194548.jpg
IMG_20210812_194808.jpg


the perimeter lighting definately works well for lighting the only micra on the stand ?

IMG_20210812_211847.jpg
IMG_20210812_211912.jpg
IMG_20210812_212028.jpg
IMG_20210812_215444.jpg


was a relaxing 1st night, ordered pizzas, few drinks, watched harlens famous wheeler dealers episode bout getting his skyline

IMG_20210812_220444.jpg


we even had a Zoom call with Max all the way from USA ?

IMG_20210812_234941.jpg
 
JAE 2021-08-13

the next morning I washed all the bugs off Kassandra and had to take a few schenic photos of course ?

IMG_20210813_112007.jpg
IMG_20210813_112047.jpg
IMG_20210813_112215.jpg
IMG_20210813_112358.jpg
IMG_20210813_112608.jpg


Nikki, Paul, Jo & Lee arrived on friday (y)

IMG_20210813_181536.jpg
IMG_20210813_181605.jpg


lol @ james new banner

IMG_20210813_181623.jpg


that afternoon, I went with alan, harlen, sebastian for some local'ish go-karting.
forgot to bring a drink or brekky so I was quite dehydrated, hungry & exhausted afterwards but it was damn good fun ???

back at the show, we got the yummy bbq & drinks going ?

IMG_20210813_191605.jpg
IMG_20210813_192605.jpg


it was a nice 8pm sunset, walking around the show especially with the skyline club smashing their pops bangs loudly, getting into trouble with security and everyone wondering over like a moth to flame ?

IMG_20210813_203418.jpg
IMG_20210813_213438.jpg


the group playing a few games on the projector and chilled out :cool:

IMG_20210814_002112.jpg
IMG_20210814_002136.jpg
IMG_20210814_002841.jpg
 
JAE 2021-08-14

Saturday being the main show day, harley in his nice K10 arrived ?
overall it was a relatively small 1/2 capacity show compared to yrs ago but at least I wasn't the only micra there. I counted 2 k10 and 2 k11 ?

IMG_20210814_095306.jpg
IMG_20210814_095324.jpg

IMG_20210814_105705.jpg

IMG_20210814_095411.jpg


thanks to chris hooded reaper for these pics

IMG_20210814_095427.jpeg
IMG_20210814_095428.jpeg


olly with the 20min spray job & red neons on the japcar stand next to us

IMG_20210814_095816.jpg
IMG_20210814_095830.jpg


a nice blue K10 behind our spot

IMG_20210814_112216.jpg


chloes plush luxury Cube

IMG_20210814_111006.jpg
IMG_20210814_111255.jpg
IMG_20210814_111023.jpg


nikki's glossy civic

IMG_20210814_111035.jpg


a few more beauties from the show

IMG_20210814_112228.jpg
IMG_20210814_113956.jpg
IMG_20210814_114056.jpg
IMG_20210814_114556.jpg
IMG_20210814_115006.jpg
IMG_20210814_115041.jpg
IMG_20210814_115449.jpg
IMG_20210814_120143.jpg
IMG_20210814_120157.jpg


lol @ the wheel clamp

IMG_20210814_125158.jpg
IMG_20210814_131935.jpg
IMG_20210814_132040.jpg
IMG_20210814_132118.jpg
IMG_20210814_132135.jpg
 
Last edited:
later that evening we played on the dodgems. there was a brief fancy dress crowd and nikki decided last min to dress as Spyro ?
best outfit imo ?

IMG_20210814_183828.jpg
IMG_20210814_183955.jpg


Represent ?

IMG_20210814_184205.jpg


pose with the lovely chloe ?

IMG_20210814_184011.jpg


throwing frisbies while I chill in back of kassandra ?

IMG_20210814_185420.jpg
IMG_20210814_185422.jpg


poor alan was absolutely shattered :ROFLMAO:

IMG_20210814_185426.jpg


a few MSC group photos ?

IMG_20210814_194200.jpg
IMG_20210814_194300.jpg
IMG_20210814_194400.jpg


9pm fireworks

IMG_20210814_210055.jpg
IMG_20210814_210341.jpg


that evening coming back from the toilet, I was surprised by Tom and everyone who were in the middle of taping some LED lights under kassandra :D

IMG_20210814_212317.jpg


omg it was recently on my mind and I love it, so I helped out tom with taping it on neatly and the end result is phwoar awesome! :love:

IMG_20210814_225509.jpg
IMG_20210814_225551.jpg


he had another spare reel of lights so I surrounded the car to highlight the body curves and the effect is amazing ?

IMG_20210814_230151.jpg
IMG_20210814_230211.jpg
IMG_20210814_230241.jpg
IMG_20210814_234935.jpg


good thing I cleaned the whole wheels cos it also lit from inside them.
so thanks to tom for planting the seed I'm definately underglowing the car :p

IMG_20210815_015055.jpg
IMG_20210815_020730.jpg


I was also delighted to be awarded the Best in Show ????
thanks james & the MSC family ?

IMG_20210815_014844.jpg
IMG_20210815_020041.jpg
 
this DIY copper cable ends I made 10yrs ago is about to snap off ?

IMG_20210822_103943.jpg
IMG_20210822_104324.jpg


so I dremelled it off

IMG_20210822_104904.jpg


brought a few 50mm2 teminal ends & crimper tool from ebay

IMG_20210821_104549.jpg
IMG_20210821_104611.jpg
IMG_20210819_201207.jpg


crimped it on

IMG_20210822_105656.jpg
IMG_20210822_110304.jpg
IMG_20210822_110656.jpg
IMG_20210822_111334.jpg


brought a spare dash gauge to replace mine with the blown airbag light ?

IMG_20210811_220015.jpg
IMG_20210811_220045.jpg


and some 10m of white LED for underneath the car ?

IMG_20210821_110635.jpg
 
spotted this cracked headlight since JAE

IMG_20210824_180611.jpg


so I brought this brand new headlight off ebay for £45, even came with fresh oem bulbs & fasteners ?

IMG_20210823_194858.jpg
IMG_20210823_194924.jpg


comparing the 25+ yr old headlights with the crystal clear new ones ?

IMG_20210824_190043.jpg
IMG_20210824_190249.jpg
IMG_20210824_190354.jpg


old indicators are getting a bit hazy so I'll use the new ones

IMG_20210824_190834.jpg


you can definately see how the new drivers headlight has a sharp clear lense whereas the old passenger side has a hazy scattered beam where the light hits all the micro fractures within the glass from years of heat cycling

IMG_20210824_192912.jpg
 
2021-08-30 Harrogate Car Show

went down to Harrogate with the CCS club for a classic car show. it was a pretty boring show with a slight drizzle

IMG_20210830_103938.jpg
IMG_20210830_093515.jpg
IMG_20210830_093532.jpg


after 3pm I popped back to the local karting track to watch some more exciting drift practice ?

IMG_20210830_161502.jpg
IMG_20210830_160801.jpg
IMG_20210830_155550.jpg
IMG_20210830_155604.jpg
IMG_20210830_154625.jpg
IMG_20210830_154705.jpg
 
Last edited:
Back
Top