• Please only use these forums for blogs, they are not a discussion forum

PollyMobiles Rebuild

OP
OP
pollyp

pollyp

Club Member
tried o-rings on the drain plug but didn't work so resealed with sealant

DSC06399.JPG
DSC06398.JPG


turbo sump fitted under new engine

DSC06400.JPG

DSC06401.JPG
DSC06403.JPG


swap the cover from the old dirty head

DSC06404.JPG
DSC06405.JPG


to the nice clean head

DSC06406.JPG
DSC06408.JPG
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
anyone knows if these universal air filters are washable cos mines abit tatty and wondered if i could use the k&n cleaning kit on it?

WS1905redconefilterside.jpg
 
Polly those hankooks are fantastic. A vastly underrated road/track compromise tyre, better than an 888 imho as it won't leave you in a ditch if the surface gets wet. I don't have experience with the 595 rs-r personally yet. Considering the price difference I think it's a no brainer.

btw don't you think the sample size in that comparison chart is too small to read anything into it?
 
OP
OP
pollyp

pollyp

Club Member
Polly those hankooks are fantastic. A vastly underrated road/track compromise tyre, better than an 888 imho as it won't leave you in a ditch if the surface gets wet. I don't have experience with the 595 rs-r personally yet. Considering the price difference I think it's a no brainer.

btw don't you think the sample size in that comparison chart is too small to read anything into it?

my cousin did suggest the rs2 first then the ad08.
this would prob only be used on a dry track and fitted onto spare pair of alloys.
that chart was only listing track tyres, though only afew
reviews of the 595rsr seems good but whether any of em translate to my setup is unknown
 
OP
OP
pollyp

pollyp

Club Member
everything swapped over to the forged engine

DSC06409.JPG
DSC06411.JPG
DSC06412.JPG
DSC06414.JPG


looking at the turbo

DSC06415.JPG


turbine is fine

DSC06416.JPG


check the gasket

DSC06418.JPG


the lapped mani/gasket face definately sealed better

DSC06419.JPG
DSC06424.JPG


turbine/gasket seal ok

DSC06422.JPG


to fix the slightly whiny worn gearbox i opened both boxes

DSC06425.JPG


the whiny noise (sounds like a whirry worn wheel bearing) was only when on the power in-gear and pitch matches engine revs so prob the input shaft bearings.
held the input shaft via the bearing casing, spun and listen, and it sounded slightly noisy like rolling a metal ball in a ceramic bowl. rocking the bearing casing it has little play.

i held & spun the shaft from the other gearbox and its very slightly quieter but rocking the bearing casing has slightly more play.

DSC06427.JPG
DSC06429.JPG
DSC06430.JPG


i know i should prob try to keep the two gear cogs matched but the secondary shafts bearing from the newer gearbox spun smoother.
so basically i swapped the input shaft from the spare gearbox into the newer silvery gearbox. hope it solves the noise

DSC06431.JPG
DSC06432.JPG
DSC06433.JPG


also tested the LSD and the preload is working

 
Last edited:
OP
OP
pollyp

pollyp

Club Member
tday i got sent a pair of correct predator FT pads and just like last time don't have to send these wrong ones back :) what a nice buncha lads

DSC06434.JPG
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
flywheel fitted

DSC06435.JPG


clutch on. thermostat on. gearbox on. every bolt has been threadlocked to make sure they don't vibrate loose again

DSC06436.JPG


the rear bush needs stiffening cos it moves too much

DSC06437.JPG


don't have any rubber to glue in but instead i figured I'd pack it with bodyfiller

DSC06438.JPG


so it sets rock solid and moulds to the gaps. not a permenant solution cos it'll prob soon vibrate out but it'll do for now

DSC06439.JPG


hmm the central beam has this rubber resonance damper to prevent it from resonating at certain frequencies. no need for that here :)

DSC06440.JPG
DSC06441.JPG


with the radiator out the exposed chassis was undersealed

DSC06442.JPG


central beam fitted

DSC06443.JPG


now ready to install the engine tomorrow
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
to simplify supporting the engine on the crane flat n level i bolted some brackets here & here, tie knot on rope ends

DSC06444.JPG
DSC06445.JPG


and it hangs level

DSC06447.JPG


engine fitted. i think the threads for the LH gearbox mount and front mount are getting weaker cos rather than suddenly tightening when the bolts are torqued up i feel it begin to strip n loosen so just stopped at that point before damaging it.

DSC06448.JPG


shafts in and filled the gearbox up

DSC06450.JPG
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
got email from brake guy saying if i could post the wrong pads back and invoice em and they'll pay me back. meh guess £100 worth of pads was too much to give away :p
 
OP
OP
pollyp

pollyp

Club Member
loom connected, radiator in, TB on.
just awaiting the turbo assembly before the alternator.
so mani & gtir elbow was wirebrushed n painted with several coats of hammerite matt black high temp paint

DSC06452.JPG
DSC06453.JPG


all the IC tubes also sprayed matt black then laquered

DSC06454.JPG
DSC06455.JPG


test fitting the heat wrap. got more than enough wrap for the mani, turbine, elbow and the downpipe

DSC06456.JPG
DSC06457.JPG


the wrapping would cover all the bolts so first the turbo's all bolted up before wrapping tomorrow

DSC06459.JPG
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
figured the best wrapping route. cut it to length, soak in water and wrap it tight

DSC06460.JPG
DSC06461.JPG


secured with ties

DSC06463.JPG
DSC06464.JPG


test fit the wrap around the elbow

DSC06465.JPG


wrapped n secured

DSC06466.JPG
DSC06467.JPG


used the remaining wrap on the downpipe

DSC06468.JPG
DSC06469.JPG


turbo assembly fitted

DSC06470.JPG


new wideband

DSC06471.JPG
DSC06472.JPG


alternator n belts on. coolant & oil filled

DSC06473.JPG


battery was at 12.5v
time to prime the oil system.
plugs out, crank for 30secs, oil light still on.
crank a further 30secs then the light goes out, continue to 40sec.
crank for 40secs twice to get the oil going around the system and through the turbo, noticable dip in crank speed when its all primed.
battery at 12v
just quickly trickle charged for an hour and its 12.9v now ready.

with oil primed, i'll recheck oil levels again tomorrow when i jack it down
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
new ducktape on the hub

DSC06474.JPG


brakes fitted

DSC06475.JPG
DSC06476.JPG


IC pipes fitted

DSC06477.JPG
DSC06478.JPG


switched back to edited forged engine map. primed oil & fuel.
nervously started her up, abit sluggish initially, idle screw too low, but soon cleared.
kept revs moving up & down within 2-3k to just warm her up. some oil smoke initially, then steam once warming up, and then clear when warm.
once warmed up i shut down to cool.





ecu temp was fine but dash temp gauge was off. found twas the sensor connector wire had broke

DSC06479.JPG
DSC06480.JPG


replaced with blade connector and works again

DSC06481.JPG


assess plugs n cylinders and it doesn't look good :(

all plugs are black n sooty. #2 had some spongy lumps trapped in it, prob PU sealant from the ptfe spacer gasket

DSC06482.JPG
DSC06483.JPG


looked in and FFS oil on the piston:mad:

DSC06484.JPG


oily coating on all piston tops

DSC06485.JPG
DSC06487.JPG
DSC06488.JPG
DSC06489.JPG


went for the first break-in drive. keeping revs up & down when stationary and drive on/off power upto 1/2 throttle between 2-4k rpm.
after 50miles its still oily:(
oil level stable, dipped down very slightly.



check warm compression and its 10.8 11.1 11.6 10.9

changing oil tomorrow then drive a further 500m 1/2 throttle in town. dunno if it'll fix itself
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
changed oil and opened the filter to inspect

DSC06490.JPG
DSC06491.JPG


afew microscopic metal bits and some muck, looks normal

DSC06492.JPG


drove the next 50-100miles of bedding-in



checking plugs, still sooty and pistons wet



driving further 50miles



the plugs are now sooty with white specks and the ground electrodes burnt white, prob from oil?

DSC06493.JPG


gonna try swapping to the hotter stock bkr5e plugs to see if that leans it out

DSC06494.JPG


bkr5e starts off like this

DSC06495.JPG


checking the almost clear oil on the shiny silver stick is tricky so i paint it matt black to see things clearer

DSC06496.JPG


checked compression and its improved since last night:
11.2 11.3 11.8 11.3 after 150m of bedding in
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
does it smoke on startup paul ?

tried to rec the exhaust during cold start (engine at 10C) earlier tday but the damn camera froze so dunno if it smoked upon cranking, but shortly after cranking the exhaust would emit the same heavy soot particles like before. once warmed up the exhaust is fine.

when i left it to cool from 2pm to 7pm and warm start her from 25C the video showed no smoke or anything at all
 
OP
OP
pollyp

pollyp

Club Member
few miles down the road the bkr6e plugs have sooted up.
compression seemed to have stabilised.

DSC06497.JPG


after now reaching 250m of break-in, the cylinders still wet.

DSC06499.JPG
DSC06500.JPG
DSC06501.JPG
DSC06502.JPG


measured that after 100m the oil's gone down 1/2 a dipstick, exactly same as before.

other than the improved compression from a tighter fitting bore, this is all a carbon copy of what happened last year with this engine.

i figure oil can only get in at this rate via the rings or stem seals.
the rings and the engine head assembly are the same as last time, tis only the bore that has been machined better.

so i'm thinking either the oil rings are crap, although the compression rings seem to be improving, or the old inlet stem seals are buggered and leaking badly? although wouldn't it smoke alot more during initial acceleration after high rev deceleration?

i'll rec tomorrow morning whether it'll smoke during cold cranking.
maybe i'll need to do dry & wet compression test to see if they're roughly the same, if yes then that may point to the stem seals
 
Last edited:

frank

Club Member
my money would be on the oil rings paul, one of mine smoked on startup in the morning (1st and 2nd gear only then stopped smoking, but drank 1 pint/1000 miles) and when i checked the rings in the bore of an empty block, i could see little arcs of daylight here and there, where they were,nt making contact with the bore (only 1 or 2 thou)
the 2 compression rings exert far more pressure on the bores but dont scrape the oil off the bores for some reason !.
the oil control rings are far thinner tho eh, and seem to scrape the bores far more efficiently with less pressure.
i,ve had the same problem with our kart engines in the past, if those oil control rings are,nt a perfect fit you get a pool of oil left on the piston crown, and oil consumption too
 
OP
OP
pollyp

pollyp

Club Member
Oh bugga more work n money :(
So should i continue breaking in the top rings n bores towards 1000miles then hopefully just replace the oil rings?
Or will the excess oil affect the bedding and or the oil rings need to be bedded in with the top rings meaning i have start ALL over again!
 
OP
OP
pollyp

pollyp

Club Member
there must be a way to diagnose for bad oil rings or bad stem seals?
i should prob try replace the simpler steam seals first before considering the big expensive task of replacing oil rings.
anyone in north east have a pressure line that i could hook up to the spark hole to hold the valves in while i replace the steam seals?
if simply replacing oil rings won't work I may as well just chuck this engine away and swap back to the original stock engine with replaced HG thats blown :/
 

frank

Club Member
i re-shaped mine paul (they,re steel/workable eh, unlike the cast compression rings) its this current engine actually.
the oil rings were totally gummed into the pistons originally, so i cleaned and stretched them, but i had slightly miss-shaped them while stretching and they had the daylight patches.
the 1st corsa piston engine had a similar problem problem (i had it underbored eh) and the arc of the ring miss matched the arc of the bore, and that one smoked horrendous !.
iirc yours were oversize rings that were gapped eh, maybe the same problem ?
i spent about 1 hour tweaking these ones till i could,nt see daylight, and it cured it :)
 
OP
OP
pollyp

pollyp

Club Member
i re-shaped mine paul (they,re steel/workable eh, unlike the cast compression rings) its this current engine actually.
the oil rings were totally gummed into the pistons originally, so i cleaned and stretched them, but i had slightly miss-shaped them while stretching and they had the daylight patches.
the 1st corsa piston engine had a similar problem problem (i had it underbored eh) and the arc of the ring miss matched the arc of the bore, and that one smoked horrendous !.
iirc yours were oversize rings that were gapped eh, maybe the same problem ?
i spent about 1 hour tweaking these ones till i could,nt see daylight, and it cured it :)

with the bore machined to a smaller tighter dia which brought the ring end gaps back to min specs, maybe the oil rings are mis-shaped. it leaks the same amount across all 4 cylinders.
how do you bend n shape the oil rings without affecting the end gaps?

wanna try the easier cheaper valve steam seal replacement first
 

sleeper_ss

Ex. Club Member
Impressed with your patience..hope it's the stem seals...
"the central beam has this rubber resonance damper to prevent it from resonating at certain frequencies. no need for that here"
Thanks..wondered what that was for.Dumped mine too,heavy affair iinit
 

frank

Club Member
with the bore machined to a smaller tighter dia which brought the ring end gaps back to min specs, maybe the oil rings are mis-shaped. it leaks the same amount across all 4 cylinders.
how do you bend n shape the oil rings without affecting the end gaps?

wanna try the easier cheaper valve steam seal replacement first
no the corsa pistons are 72.5mm paul, but mine were well worn so i asked him to underbore it by 15" thou so i could regap the rings the smaller 72.2mm ish (and i honed the pistons down to a nice snug fit)
but when i gapped the rings down they did,nt fit the bores properly (as in pic, the arc of daylight showing on the righthand side)

P5070010.JPG
 
OP
OP
pollyp

pollyp

Club Member
i shoulda checked for that gapage when i was checking the oil ring end gaps :( well now i know for next time

wideband very sooty so taking it out for now to stop the soot wrecking it

DSC06503.JPG


recorded the cold start this morning and it struggles to get going on its own due to the oil so had to apply abit of throttle.
it smokes badly for the first few secs of burning that oil pool, then runs better as its burnt off and clear into steam but at 1:30 a whole ploom of wet soot comes gushing out coating everything



once warmed up after a mile it appears to be clear at idle



drove from 175 towards 300m of break-in, tested dry & wet compression and got:

cyl1 cyl2 cyl3 cyl4
11.3 11.6 11.9 11.2 dry
12.1 12.2 12.4 12.1 wet
00.8 00.6 00.5 00.9 difference

its all gone up almost 1 bar so maybe the old rings are shot?

the pistons always wet whether i'm cranking it freely with or without plugs.
after free cranking, large amounts of oil can be seen creeping inwards from all sides (inlet port top, exhaust port bottom), mostly from the inlet side, the same way amonst all cylinders.

DSC06504.JPG
DSC06505.JPG
DSC06506.JPG


restarting the warm engine, didn't smoke at idle just the same oily soot but first dab of WOT towards redline and it smokes blue/white from the excess oil, then began recording the video. less smoky the next time, just very rich and hint of oil smoke



almost losing the plot with this damn engine now. all that work for nothing.
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
thinking back in Jan, when i was reinstalling the valves back into the head, i think the inlet valves popped through the stem seals easier than the exhaust valves so maybe they were worn?
 

frank

Club Member
thinking back in Jan, when i was reinstalling the valves back into the head, i think the inlet valves popped through the stem seals easier than the exhaust valves so maybe they were worn?
wishfull thinking paul :)
i doubt if its the stem seals personally mate, it would smoke mainly after lift or @ wot after prolonged idle eh.
its like the oil control rings are,nt scraping the oil off the bores on the downstroke, but the 2 compression rings are scraping the oil upwards on the upstroke eh !.
the rings are easy to rework, with patience :)
 

Stani1029

Club Member
This is why i stick to stock pistons, if you have the patience to repair this then all credit to you polly! How much boost you planning to run anyway on the forged setup and what hp would you be happy at?
 
OP
OP
pollyp

pollyp

Club Member
yeah sounds like the top rings are doing their job sealing on the upstroke but the oil ring doesn't on the downstroke.

there's slight oil smoke for a milisec at WOT after prolong idle till fuel catches up and gets very rich with black smoke.

easy stuff before hard, change stem seals before piston rings.
gonna stuf a long rag into the cylinder, turn to TDC to wedge the valves then i think i'll get this OHV spring tool to remove the spring then change the stem seals.

mnuxa1S4pLAqXAbqz2eDfmg.jpg

http://www.a1plantsales.com/Overhead-Valve-Spring-Compressor-OHV-Sealey-VS160_AZQO2.aspx

test procedure out on my spare engine first
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
This is why i stick to stock pistons, if you have the patience to repair this then all credit to you polly! How much boost you planning to run anyway on the forged setup and what hp would you be happy at?

the issue is prob me not checking the rings were gapped/shaped and sealing properly and/or ignoring to replace easy stem seals rather than the piston itself :/

i'd be keeping it at 10psi, just wanted to swap to forged for more reliability and have the potential to handle more power in the future, hehe how wrong this is turning out to be :rolleyes:
 

Stani1029

Club Member
I suppose but you cant blame yourself, 3rd time lucky maybe? Youve got great patience! Id have given up the first time round! As for reliability we'll see how long mines lasts at 14psi :D
 
OP
OP
pollyp

pollyp

Club Member
removed injectors to peak inside the inlet valves for oilyness

DSC06507.JPG


no major signs of dripping oil down the stem

DSC06509.JPG


but the back of the valves quite shiny oily

DSC06510.JPG
DSC06511.JPG


trying to purge out the little pool of oil off the piston by cranking was tricky, just stays there.
so i tried to stuff a rag down the plug hole to soak the pool up

DSC06512.JPG


cranked with no compression for 40sec, piston still dry, no oil seeping in.
cranked with plugs in, piston still dry.
not accurate test by any means and oil is cold (try again when its warm) but least at cranking speed the rings are not leaving a serious amount of oil on the walls.

when i saw the oil seeping inwards after cranking earlier, maybe the oil itself had slowly accumulated there from the leaky stem seal then the warm pool of oil was simply spread across the whole piston face during the movement of cranking, rather than vapourise out the plug hole like fuel, and then once stopped, the thin oil just creeps back down the dome face under gravity?
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
Last edited:
OP
OP
pollyp

pollyp

Club Member
removed cover

DSC06513.JPG


oils already black

DSC06514.JPG
DSC06515.JPG


noted timing

DSC06516.JPG
DSC06517.JPG
DSC06518.JPG


set the piston to BDC. to wedge the valves i found some thin rope to stuff down the plug hole. using a tube thats slightly bigger bored than the rope to help guide it down without kinking

DSC06519.JPG


turn the crank till it resists. now the rope is wedged up securely against the valves by the piston

DSC06520.JPG
 
Last edited:
OP
OP
pollyp

pollyp

Club Member
was looking at either getting a pair of 2nd hand 15" alloys upto £100 or ideally finding someone who sells single rota grids (to keep the same look and unspring weight) for the 595rsr.

most rota suppliers only sell a 4 set but i've managed to find on ebay a US seller who sells single rota grid alloys for approx £73 each plus post and tax and custom totaling prob from £200. need to find how much tax n custom it'll be before considering

http://www.ebay.co.uk/itm/1-ROTA-GR...&otn=3&po=LVI&ps=63&clkid=8282117444010439564
 
Top